Alfa Laval ALTB-SB-20, Инструкция по эксплуатации

Страница: 46 / 74

8 Appendix
Ensure totally clean surfaces during mounting. Always use original Alfa Laval parts.
Product information
Klübersynth UH1 6 oils
Synthetic gear and high-temperature oils for the
food-processing and pharmaceutical industries
Klübersynth UH1 6-100, 150, 220, 320, 460, 680, en Edition 12.09, replaces edition 07.09
article number: 096094, 096058, 096059, 096063, 096060, 096064 MA-TM/HSi
Product data
Klübersynth UH1 6- …
100 150 220 320 460 680
Marking acc. to DIN 51502 CLP PG
100
CLP PG
150
CLP PG
220
CLP PG
320
CLP PG
460
CLP PG
680
Marking acc. to ISO 12925-1
CKC 100 CKC 150 CKC 220 CKC 320 CKC 460 CKC 680
NSF-H1 registration*, registration no. 137872 124437 124438 124439 124440 124441
ISO VG DIN 51 519 100 150 220 320 460 680
Density, DIN 51 757, at 15 °C,
[kg/m³], approx.
1040 1050 1060 1065 1075 1075
Kinematic viscosity, DIN 51 562, pt. 01
at 20 °C, [mm
2
/s], approx.
at 40 °C, [mm
2
/s], approx.
at 100 °C, [mm
2
/s], approx.
250
100
19.5
390
150
28.5
610
220
41 840
320
56 1270
460
78 1900
680
115
Viscosity index, DIN ISO 2909, approx. > 190 > 210 > 220 > 220 > 240 > 250
Flash point, DIN ISO 2592, [°C] > 220 > 220 > 220 > 220 > 220 > 220
Pour point, DIN ISO 3016, [°C] < -45 < -35 < -35 < -30 < -30 < -25
Foaming characteristics, ASTM D 892,
sequence I, II, III [ml]
< 100/10
Copper corrosion, DIN EN 2160, 24 h,
corrosion rating
1 - 100
Corrosion protection on steel,
DIN ISO 7120
0 – A
Ageing characteristics, ASTM D 2893,
increase in viscosity, [%]
< 6
FZG gear test rig, A/8.3/90
DIN 14635-1, scuffing load stage
> 12
FZG gear test rig, A/16.9/90
DIN 14635-1, scuffing load stage
> 11 > 12
Rolling bearing test rig FE 8, D 7,5/80-80,
DIN 51 819-3, wear of rolling elements,
[mg]
< 30
Lower service temperature range**, [°C] -35 -30 -25
Upper service temperature range**, [°C] 160
* This lubricant is registered as H1, which means that it has been designed for incidental, technically unavoidable food contact. Experience shows that it can be
used for equivalent applications in the cosmetic and pharmaceutical industry under the conditions described in the product information leaflet. Specific test
results as e.g. biocompatibility, which could be an additional requirement for applications in the pharmaceutical industry, are not available for this product.
Therefore, before using the lubricant adequate risk analyses should be performed and, if necessary, suitable measures be taken by the manufacturer and user
of installations in order to exclude the risk of health hazards and personal injuries.
** Service temperatures are guide values which depend on the lubricant's composition, the intended use and the application method. Lubricants change their
consistency, shear viscosity or viscosity depending on the mechano-dynamical loads, time, pressure and temperature. These changes in product characteristics
may affect the function of a component.
46