GB 16
GB
Driving with the lawn tractor
•
Push the right-hand pedal (clutch/brake) right down
- possibly engage with the stop lever.
The mowing appliance must not be switched on.
•
Start the engine.
•
When the engine is running, select the corresponding forward or
reverse gear. With a hydrostat drive, pre-select the corresponding
position in forward or reverse drive.
For the first use of the lawn tractor, we would advise that you only
choose 1st gear or set the hydrostat drive to MIN.
•
To start motion, slowly release the clutch/brake pedal.
Attention!
Do not switch the 5-gear transmission while driving.
The lawn tractor must be stationary in order to change gear.
Brakes
•
Press the right-hand pedal
down completely in order to brake.
Switching the mowing appliance on
•
Only switch the mowing appliance on with the engine running.
•
Put the gas lever into the
position.
•
Put the mowing appliance switch onto position
"I"
.
•
Set the required cutting height.
Attention!
Before switching the mowing blade on, allow the engine to warm
up for about 1 minute!
When you switch the mowing appliance on, the mower should not
be standing in long grass. Set to the highest cutting height.
Switching the mowing appliance off
•
Put the mowing appliance switch onto position
"0"
.
•
The mowing appliance can be switched off both at a standstill and
also during movement.
Attention!
A rotating / slowing blade can cut hands and feet.
Therefore, keep your hands and feet away from the blades.
Setting the cutting height
The blades are raised and lowered with the position lever
to the right of the driver's seat.
Six height settings with a cutting height between 30 and 90
mm are possible.
Allow the position lever to engage at the height adjustment
position required.
Adjustment of the cutting height can be done both at a
standstill and also during movement.
Attention:
Set the highest cutting height:
- before switching the cutting appliance on
- when driving without mowing
Driving without traction
(pushing)
Attention!
Only with the engine switched off and the blades stationary!
a) For a 5-gear transmission:
1. Put the switch lever into position 0.
2. Release the brake.
b) For a hydrostat drive:
1. Remove or lift up the grass box.
2. Pull out bypass lever
and engage downwards
.
3. Release the brake.
The lawn tractor can now be pushed without any difficulty.
Driving and mowing
In order to achieve a tidy mowing result, the traction speed must
be adapted to the state of the lawn.
a) Lever position for hydrostat drive:
- long / thick grass and wet grass: 0 - ¼
- normal grass, weekly cutting: ½ - 2/3
The lever positions from 2/3 - 1/1 are reserved for driving
without mowing.
b) Lever position for 5-gear transmission:
- long / thick grass and wet grass: 1st gear
- normal grass, weekly cutting: 2nd - 3rd gear
4th and 5th gear are reserved for driving without mowing.
In a normal case, the cutting height is about 4-5 cm. This corresponds
to the 2nd/3rd position of the height adjustment. Cut moist or wet grass
with a higher cutting height.
The best thing to do with very long grass is to cut it twice. For the first
cut, set the machine to max. cutting height and set it to the required
height for the second cut.
39
40
37
38
Содержание 110918
