AJA Io Express Скачать руководство пользователя страница 86 | Manualshive

Страница: 86 / 132

background image

76

AJA Capture
Options Panel

Using the Capture Options panel you can change or adjust details for the selected Preset. The
following settings can be accessed:

General – change Editing Mode and Timebase for the Adobe Premiere Pro CS5 project
and access Playback settings for Io Express output. Adobe Premiere Pro CS5 Desktop
Display, Preview Rendering, and Timeline options are also available.

AJA Capture Options panel

Capture Options

Under Capture Options, select the appropriate formats and settings for your project. In
Io Express operation, the Primary Format is the captured media format written to disk.
Secondary format is for other AJA devices that perform format conversion.

The Primary Format menu allows you to select the video format used in your current project.
The Secondary Video Format allows you to perform down-conversion of input or output
video.

Analog output is always available.

Primary and Secondary Video Options Supported by Io Express

See “About Primary & Secondary Video Formats” on page 2 for Primary/Secondary video
format and down-conversion information.

«
...
84
85
86
87
88
...
»

Содержание Io Express





































































































































Отзывы:

Нет отзывов

Похожие инструкции для Io Express

Endura AZ20 series

Бренд: ABB Страницы: 8

Бренд: Calsense Страницы: 4

Бренд: IFR Страницы: 46

Zetasizer Nano Series

Бренд: Malvern Страницы: 16

Бренд: OHAUS Страницы: 19

Бренд: OHAUS Страницы: 54

Бренд: Zenner Страницы: 2

Бренд: Xantrex Страницы: 2

Бренд: Xaoc Devices Страницы: 8

Clavinova CVP-601

Бренд: Yamaha Страницы: 98

Бренд: Yamaha Страницы: 28

Бренд: YOSensi Страницы: 27

Бренд: bmcm Страницы: 5

Бренд: Tektronix Страницы: 48

Бренд: LumaSense Страницы: 23

Litemaster Pro L-478DR

Бренд: Sekonic Страницы: 16

Бренд: Clavia Страницы: 13

Бренд: Chauvin Arnoux Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды