AJA Io Express Скачать руководство пользователя страница 73

Страница: 73 / 132

Io Express Installation and Operation Manual — Setup Window

Video/Audio

Use this pull-down menu to select the video/audio input combination you will capture:

•

Video Only

•

Audio Only

•

Video – (minus) Audio – video and audio are recorded in separate files

•

Video + (plus) Audio (QuickTime only) – video and audio are recorded in the same file

The options shown are determined by the selected file format. QuickTime captured audio is
either embedded with the video file or captured to separate .mov files. All other formats capture
audio to Wave Files.

Video Subtype

Video Capture Formats supported by Io Express cards (varying according to file type) include:

•

8-bit YUV 4:2:2 – ’2vuy’

•

8-bit YUV 4:2:2 – ’2Vuy’

•

10-bit YUV 4:2:2 – ’v210’

Audio Subtype

Audio Capture Formats supported by Io Express cards include:.

•

48 kHz 16-bit PCM Mono

•

48 kHz 16-bit PCM Stereo

•

48 kHz 24-bit PCM Mono

•

48 kHz 24-bit PCM Stereo

•

48 kHz 32-bit PCM Mono

•

48 kHz 32-bit PCM Stereo

Io Express 2K also supports 96 kHz 16 through 32-bit PCM Mono and Stereo selections

Audio Track

Select the number of audio tracks for this project. Io Express models support up to 8 tracks.

Содержание Io Express





































































































































Результаты поиска

Содержание Io Express

Отзывы:

Похожие инструкции для Io Express

Бренды по названию

Популярные бренды

AJA Io Express, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Io Express

Отзывы:

Похожие инструкции для Io Express

Бренды по названию

Популярные бренды