manualshive.com logo in svg

AIXTRON CRIUS II, Системное руководство

Поделиться
Скачать
AIXTRON CRIUS II Скачать руководство пользователя страница 67

AIXTRON

 - Dokumentation

CONFIDENTIAL

67

3

cr

ius_I

I_e

n_

00,

 Ed

it

io

n 

06/

201

0

System Manual

Description

CRIUS II

Reactor

3.5.4

Temperature control unit

The temperature control unit consists of the following controllers:

Eurotherm

The Eurotherm temperature controller is used to control the system from ambi-
ent temperature up to 1200 °C. It is located at the reactor cabinet. It measures 
the temperature at the bottom of the susceptor using a thermocouple.

Fig. 3-15

Temperature measurement at the bottom of the susceptor

A Eurotherm controller
B Heater coil
C Thermocouple

Mikron pyrometer

A Mikron pyrometer is used to measure the temperature on the top surface of 
the susceptor (black body radiation). It is located inside the glove box. Using 
a four channel pyrometer allows all three heater zones to be measured. The 
zone power ratio may be adjusted to ensure a flat temperature profile across 
the susceptor.

The black body radiation is measured through the pyrometer probes, mounted 
on the showerhead.

There are five pyrometer probes on the showerhead to allow full access to all 
heater zones.

Fig. 3-16

Temperature measurement on the top surface of the susceptor

A Mikron controller
B Pyrometer probe

Содержание CRIUS II



































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды