AIXTRON CRIUS II Скачать руководство пользователя страница 188

Страница: 188 / 194

ius_I

I_e

00,

06/

201

188

CONFIDENTIAL

AIXTRON

- Dokumentation

Storage, disposal

System Manual

Disposal

CRIUS II

7.2.5

Recycling of materials

Materials which are not contaminated with chemicals should be recycled.

The following components are contaminated and

must not

be recycled:

•

Tubing and valves of the process gas system

•

Reactor

•

Components in the process chamber

These components must be classified as hazardous waste and brought to a
specialized hazardous waste disposal company.

CAUTION!

Contaminated materials.

Contaminated materials are harmful for the environment.

Materials which are contaminated with chemicals must not be recycled.
Dispose of these components as hazardous waste according to the reg-
ulations.

NOTE:

The above assessment is based on the baseline process. If the system
is used for other processes, then the user must adapt the recycling and
decommissioning process to ensure safe disposal.

Содержание CRIUS II



































































































































































































Результаты поиска

Содержание CRIUS II

Отзывы:

Бренды по названию

Популярные бренды

AIXTRON CRIUS II, Системное руководство

Результаты поиска

Содержание CRIUS II

Отзывы:

Бренды по названию

Популярные бренды