AIXTRON CRIUS II Скачать руководство пользователя страница 150

Страница: 150 / 194

ius_I

I_e

00,

06/

201

150

CONFIDENTIAL

AIXTRON

- Dokumentation

Maintenance

System Manual

Main power supply

CRIUS II

Checking the remote
control switching
function

Fig. 6-6,

150 shows the main switch. It is located in the electrical cabinet.

Check the switching function of the main switch using a screw driver

Fig. 6-6

Main switch

Checking the RCD

The main switch also acts as a residual current device (RCD). If current leak-
ing out of the circuit (e.g. current leaking to earth) exceeds the safety limits,
the main switch disconnects and jumps to the «trip» position.

The RCD can be tested to see if it is operational. Proceed as follows:

Make sure that the system is in a state where it may be switched off
safely

Open the door of the electrical cabinet at the rear side

Press the [TEST] button (item F in Fig. 6-6,

150)

•

This button creates a residual current

•

The main switch jumps to the «trip» position

Press the [RESET] button (item G in Fig. 6-6,

150) to reset the resid-

ual current device

Turn the main switch back to the «I» position

A «Manual - Auto» switch
B «On - Off» switch
C Plastic bow for locking
D [push to trip] button

E Tripping characteristics
F [TEST] button
G [RESET] button
H Tripping characteristics

NOTE:

Never change the tripping characteristics of the RCD.

Содержание CRIUS II



































































































































































































Результаты поиска

Содержание CRIUS II

Отзывы:

Бренды по названию

Популярные бренды

AIXTRON CRIUS II, Системное руководство

Результаты поиска

Содержание CRIUS II

Отзывы:

Бренды по названию

Популярные бренды