AIXTRON CRIUS II Скачать руководство пользователя страница 168

Страница: 168 / 194

ius_I

I_e

00,

06/

201

168

CONFIDENTIAL

AIXTRON

- Dokumentation

Maintenance

System Manual

Vacuum system

CRIUS II

6.11.6 Searching for leaks

A leak test is required every time after the vacuum system has been opened.
The leak test is required for the following reasons:

•

Air leaking into the system may impair the process and thus the product
quality

•

Hydrogen is used as a process gas. Air leaking into the system may lead
to the formation of an explosive gas mixture.

Proceed as follows to search for leaks:

Connect the inlet of the He leak detector to the vacuum system

Connect the outlet of the He leak detector to a suitable exhaust system

Perform a leak search as described in the OEM manual for the He leak
tester and according to the requirements of the SEMI standard

WARNING!

Hazardous gases.

The vacuum system may contain harmful or flammable gases. These
chemicals end up in the waste gas of the He leak detector. Inhalation of
toxic or caustic gases may impair your health and even lead to death.

Connect the outlet of the He leak detector to the exhaust system. Do not
release these gases into the open air.

Содержание CRIUS II



































































































































































































Результаты поиска

Содержание CRIUS II

Отзывы:

Бренды по названию

Популярные бренды

AIXTRON CRIUS II, Системное руководство

Результаты поиска

Содержание CRIUS II

Отзывы:

Бренды по названию

Популярные бренды