AIC WAIKATO Presto Detacher 70100 Скачать руководство пользователя страница 21

Страница: 21 / 67

Presto Detacher

™

608-526-6882

1.Determine the best location for the sensor, taking into consideration the best milk hose

management of the milk hose from the milking unit.

2. Determine the correct orientation of the SS mounting plate, (RH or LH mount). To do so notice

the orientation of the threaded bolt holes in the SS plate. The single threaded bolt hole is

always in the upper portion of the plate. Flipping the plate over reverses the sensor mounting

for Right or Left hand sensor mounting.

3.The SS mounting plate can be welded, bolted or banded to a solid mounting location.

4.To assure consistent milk slugging

all the SS mounting plates must be horizontally

leveled and vertically square.

5. After the SS mounting plate is installed. Place the flow cell into the plastic holder block, hold it in

line with the threaded holes in the SS mounting plate and tighten the bolts. It works best to tighten

the upper bolt first.

The Single

Threaded Hole

should always be

on the top. To

create RH mount

flip the bracket

over.

Flow Cell

Stainless Steel Mounting

Plate Shown for:

Left

Hand Sensor Mount:

Notice The threaded hole

pattern.

Hardware Installation

50111 Flow Cell Holder

Содержание Presto Detacher 70100




































































Результаты поиска

Содержание Presto Detacher 70100

Отзывы:

Похожие инструкции для Presto Detacher 70100

Бренды по названию

Популярные бренды

AIC WAIKATO Presto Detacher 70100, Руководство по установке

Результаты поиска

Содержание Presto Detacher 70100

Отзывы:

Похожие инструкции для Presto Detacher 70100

Бренды по названию

Популярные бренды