Agria 5400 KL Скачать руководство пользователя страница 45

Страница: 45 / 68

agria

Power Mower 5400

Municipal Mower 5400 KL

Steering Handle Central Mounting

Re-tighten adjustment nut (3) with 100
Nm after the first 4 operating hours, then
after every 50 operating hours.

Remove pin retention to unscrew fas-

tening nut for steering handle (5).

Remove steering handle and place

aside.

Loosen lock nut (4).

Tighten adjustment nut (3) with 100

Nm.

Re-tighten lock nut (4) (lock).

Mount steering handle. Brush some

lubrication grease onto gliding faces, if
necessary.

Screw on fastening nut (5) until steer-

ing handle is without play but can still
be swivelled. Secure with pin.

Steering Handle Pendulum Stop

This 2-axle-steering handle bearing
provides optimum dampening when
each of the two stop buffers is adjusted
to a play of A = 0.5 mm (in position zero,
with no load on steering handle) to the
stop plate.

Adjustment:

Loosen hexagonal nuts (2).

Adjust stop buffer (1) by turning it to

the above stated play.

Re-tighten hexagonal nut (lock).

1 Stop buffer
2 Lock nut for stop buffer
3 Adjustment nut for steering handle central

mounting

4 Lock nut
5 Fastening nut for steering handle

100 Nm

(4) 50 h

5. Maintenance

Содержание 5400 KL





































































Результаты поиска

Содержание 5400 KL

Отзывы:

Agria 5400 KL, Руководство по эксплуатации, Страница: 45 / 68

Результаты поиска

Содержание 5400 KL

Отзывы: