Agria 5400 KL Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 68

Agria 5400 KL Скачать руководство пользователя страница 37

agria

Power Mower 5400

37

4. Commissioning and Operation

Caution with hot engine parts!

The exhaust and other engine parts
become very hot, if the engine runs
and immediately after turning off. Hold
for sufficient distance from hot
surfaces and keep children away from
the running engine.

Danger Zone

W

Keep out of the mower’s dan-

ger zone during starts and

operation.

Mowing on Slopes

W

To prevent the mower from

sliding on slopes, make sure it

is secured by another person us-
ing a bar or a cord. This person must
be located at a higher position than
the vehicle and at a safe distance
from the attachment at work.

For operation on banks, always turn
machine towards the slope!

Starting the engine on slopes

Keep the mowing drive and the

travelling drive in engaged mode; brak-
ing effect.

Move the hand clutch lever and

emergency-off-switch to "Start" posi-
tion.

Start the engine.

4

1.

2.

Mowing on

plain surfaces

Mowing on

slopes

4

è

I

Danger zone

«
...
35
36
37
38
39
...
»

Содержание 5400 KL





































































Отзывы:

Нет отзывов