Agria 5400 KL Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 68

Agria 5400 KL Скачать руководство пользователя страница 36

36

agria

Power Mower 5400

4. Commissioning and Operation

Mowing

Grease the crank stone
(Planetary mowing drive)

Remove knife guard..

Grease the cutter bar.

Start the engine.

è

Comissioning

W

Check safety circuit function

- only operate the machine if the
safety circuit is working.

Wear protective ear plugs and solid

shoes.

Engage proper gear.

Engage mowing drive.

Engage wheel drive.

Pull hand clutch lever slightly while

pressing the throttle.

I

After mowing and in case of
grass clogging:

Move F/R hand lever to “neutral” , The

mower comes to a stop but not the knives,
thus freeing the cutter bar from grass.

Disengage mowing drive.

Shut engine off.

Refit knife guard.

For direction change from forward to
reverse, proceed as follows:

Engine to idle speed.

Pull hand clutch lever and hold.

Move the shifter to "R" and hold.

Slowly release the hand clutch le-

ver while you are pressing the throttle.

Re-tighten all nuts and screws of the mowing drive and the
cutter bar after commissioning and when changing the knife
after about 15 - 30 operating minutes and than every 4 oper-
ating hours (particularly of the cutter bar carrier, knife driver
and cutter bar mounting flange).

è

0

4

è

I

1.

2.

«
...
34
35
36
37
38
...
»

Содержание 5400 KL





































































Отзывы:

Нет отзывов