Agria 5400 KL Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 68

Agria 5400 KL Скачать руководство пользователя страница 32

32

agria

Power Mower 5400

4. Commissioning and Operation

Commissioning

Please note that durability and operational safety of the engine depend to a large
extent on its breaking-in. Always allow a cold engine to warm up for some min-
utes and never run it at full throttle at the beginning.

Please note: for the first 20 hours of operation (break-in period) do not use the
engine at full power.

Make sure you check and maintain air filters regularly and use clean fuel.
Only use branded petrol.

Only use fresh, clean fuel (not older than 3 months) and approved fuel cans to be
purchased in special shops. Rusty sheet metal cans or fuel cans not suited for
petrol are not permitted.
For the first commissioning or after longer periods of no operation, fill fuel tank to
maximum to avoid starting problems.

Be careful when dealing with fuel.

Fuel is easily inflammable and explosive in certain conditions!

l

Do not refill in closed rooms.

l

Before each fuel fill, shut off the engine and

wait until it has cooled off.

l

Never refill close to open fire, inflammable

sparks or hot engine parts.

l

Do not smoke during filling!

l

Do not spill any fuel, use a proper filling de-

vice.

Do not cause fuel tank to overflow, but leave a 5

mm margin for the fuel to expand.

l

Check transmission oil level (see page 43)

4

I

Note: For reasons of transport, the engine
is not filled completey with engin oil!

Before you operate the engine the first time,
fill in engin oil (see page 38)!

«
...
30
31
32
33
34
...
»

Содержание 5400 KL





































































Отзывы:

Нет отзывов