manualshive.com logo in svg

Agilent Technologies Magnis Dx NGS Prep System, Руководство пользователя

Поделиться
Скачать
Agilent Technologies Magnis Dx NGS Prep System Скачать руководство пользователя страница 70

Magnis and Magnis Dx NGS Prep System User Guide

70

Figure 47

Hardware Usage Tracking screen

UV Tube

Next to this check box is displayed the number of hours, minutes, and seconds of usage for the 
UV tube. Marking the check box enables the Reset button

Reset

This button resets the usage tracker for the UV tube to zero. Once reset, the usage is displayed as 

0h 00m 00s

. 

This action should only be performed by an Agilent engineer or Agilent authorized 

service provider following replacement of the UV tube.

Close

This button returns you to the Settings screen.

Instrument Diagnostic screen

Purpose: To run diagnostic tests on the instrument and access reports for previous diagnostic 
tests and instrument health checks. See instructions in 

“Perform instrument diagnostic tests” 

on 

page 38.

To open: From the Home screen, press 

Settings

. On the Settings screen press 

Self Diagnostic

. 

NOTE

The lifespan of the UV tube is 630 hours. After 630 hours of usage, when a 
decontamination cycle is initiated, the system notifies you to replace the UV 
tube. 

Содержание Magnis Dx NGS Prep System

































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды