manualshive.com logo in svg

Agilent Technologies G8610A, Руководство по эксплуатации

Поделиться
Скачать
Agilent Technologies G8610A Скачать руководство пользователя страница 99

Agilent Technologies Helium Leak Detector 

DRAFT 12/1

1

/17

99

NOTE

The smallest mass flow meter that may be used while still 
functioning. It could be as small as 300 SCCM, though this flow 
rate may not be capable of reading mass flow when measuring 
flows of mobile unit leak detectors (units with larger roughing 
pumps).

Alternatively, if using a mass flow meter that is not supported by the leak detector software 
(anything other than Alicat Scientific brand mass flow meter):

1. Attach the mass flow meter in series above the Agilent power probe sniffing gun (Agilent 

part number K9565306).

2. Attach the mass flow meter to the sniffing gun through use of a KF to compression port 

adapter, 1/8" to NW25 (Agilent part number KCP250125), if using the power probe as 
the metering valve (Figure 5-22).

3. Perform an internal calibration.

4. Perform an external calibration using the sniffing probe by:

a. Selecting 

Calibration > Calibrate With > External Leak.

b. Entering the value of the external calibrated leak. Keep the probe at the inlet of the 

standard leak.

c. Pressing 

Calibrate.

Figure 5-22  External Sniff Calibration Setup

5. Select 

Test Configurations > Applications Setup

.

6. Select 

PPM Sniff Method > Application Setup.

7. Ensure the system is in 

Test

 and the test port pressure adjusted between 5E-1 Torr 1 Torr.

8. Select the 

MFM

 option.

9. Input the flow rate - SCCM displayed from the MFM/MFC controller.

The leak detector is now ready to measure the concentration of Helium in PPM.

To make the connection between the power probe sniffing gun and the mass flow meter:

1. Fit the mass flow meter on the low-pressure end with an NW25 vacuum fitting 

(Figure 5-23). 

Содержание G8610A

















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды