manualshive.com logo in svg

Agilent Technologies G8610A, Руководство по эксплуатации

Поделиться
Скачать
Agilent Technologies G8610A Скачать руководство пользователя страница 22

Agilent Technologies Helium Leak Detector 

22

DRAFT 12

/1

1/17

❑

Allow an adequate distance (2 to 3’) from the back of the 
leak detector to the power source. This ensures easy access 
to the power cord for connecting or disconnecting purposes. 

Spectrometer

WARNING

Store the Ion Source/Preamplifier sub-assembly in a cool, dry 
area in a tightly sealed, ESD protected container. Wear lint-free 
gloves when handling the spectrometer. Wash hands 
thoroughly after handling the spectrometer filaments and 
especially before smoking or eating.

CAUTION

The spectrometer operates at a very high vacuum produced by 
the high vacuum pump. Service of the spectrometer requires 
that this vacuum be vented to the atmosphere.

CAUTION

Do not use grease or any other substance on O-rings or metal 
seals that will come in contact with the spectrometer.

CAUTION

If the spectrometer magnet comes in contact with a magnetic 
surface, the magnet can become degraded causing the 
spectrometer to lose sensitivity.

Pumps

WARNING

To avoid injury, use proper lifting techniques when moving 
pumps. Two people may be required to move pumps safely.

WARNING

The vacuum pumps are also compressors; incorrect operation 
may be dangerous. Study the Mechanical Pump Operation 
Manual enclosed with your pump before starting pumps.

The pumps are designed to prevent any thermal risk for user 
safety. However, specific operating conditions may generate 
temperatures >70 

C.

Hot oil burns the skin. Service of the pumps in this area must be 
performed by authorized personnel only. Stand back from a 
mechanical pump before starting it.

Содержание G8610A

















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды