Agilent Technologies G8610A Скачать руководство пользователя страница 129

Страница: 129 / 176

Agilent Technologies Helium Leak Detector

DRAFT 12/1

/17

129

7.4.1.5 Current Setup

The current setup menu displays all activated parameters including selected applications.

7.4.1.6 Turn Off

Figure 7-16 Power Off

This feature provides a soft shut down for the CPU and turbo pump prior to turning off the
main power/circuit breaker switch.

NOTE

This power off feature provides a two-minute braking
procedure for the turbo pump. This aides in turbo pump life
and for safe transportation of the leak detector

Range Stop

See Section 4 “Calibration Screen”
on page 65.

Range Stop

[Exp]

System is set to display the most
sensitive leak rate range, 10

[Exp]

The range stop line shows only if
range stop is on.

Reject Set Point

See Section 7.4.1 “Current Setup
Menu” on page 128.

Reject# 1,2,3,4 Active Reject set points displayed are active;

this line is blank when all set points
are disabled or inactive.

Split Flow

See Section 5.1.3.9 “Split Flow” on
page 89.

Shows split flow, only if the feature is
turned on. To change the status, go to
the Advanced Parameters screen.

Vent Lockout Status

See Section 3.1.2 “Menus Screen” on
page 63.

Shows the status of the vent lockout
feature only if it is on.

To change the

status of the vent lockout feature, go
to the Control Panel access screen.

Table 7-3 Current Setup Screen Conditions (Continued)

Condition

Display

Description

Содержание G8610A

















































































































































































Результаты поиска

Содержание G8610A

Отзывы:

Бренды по названию

Популярные бренды

Agilent Technologies G8610A, Руководство по эксплуатации

Результаты поиска

Содержание G8610A

Отзывы:

Бренды по названию

Популярные бренды