manualshive.com logo in svg

Agilent Technologies G8610A, Руководство по эксплуатации

Поделиться
Скачать
Agilent Technologies G8610A Скачать руководство пользователя страница 107

Agilent Technologies Helium Leak Detector 

DRAFT 12/1

1

/17

107

Range

Configures 

Minimum Range

 (Range Stop) and 

Only Show 

Range 

(Manual) 

Leak Rate

 options

❑

Only Show Range

 - Configures the leak detector so that it 

only displays the pre-selected decade entered in the manual 
range variable field. For example, if the manual range 
feature was enabled and the manual range variable was set 
to E-6, then the leak rate decade displayed on the LED bar 
graph during testing would be the E-6 atm cc/sec range only. 
This feature is useful when the concern is only with 
monitoring the leak rate measurement within a single 
decade. 

For example, if the Only Show Range feature was enabled 
and the Only Show Range variable was set to 10

06,

 then 

the leak rate decade displayed on the LED bar graph during 
testing would be the 10

06

 atm cc/sec range only. 

❑

Minimum Range

 - Configures the leak detector so that it 

only auto-ranges down to the pre-selected decade. To allow 
auto-ranging to the maximum sensitivity of the system, turn 

Maximum Range Off

.

This feature is useful when a product specification is more 
than one decade less stringent than the actual sensitivity of 
the leak detector. If the leak detector is capable of displaying 
full scale < E-11 atm cc/sec, but the test specification is only 
in the E-7 atm cc/sec range, then setting the range stop to 
E-8 atm cc/sec would reduce the test cycle time by 
eliminating the need for the leak detector to reach its most 
sensitive scale during each test cycle.

Activating the Minimum Range extends the sensitivity 
requirements for calibration, thus eliminating unnecessary 
calibration errors (see Table 2-4).

NOTE

Activating the range stop extends the sensitivity requirements 
for calibration, thus eliminating unnecessary calibration errors 
(Table 6-1).

Table 6-1  Range Stop/Sensitivity Requirements

Range Stop

Max Gain

MDL

OFF

6.9

5.00E-12

ON at

-11

6.9

5.00E-12

-10

10

5.00E-11

Содержание G8610A

















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды