Agilent Technologies G8610A Скачать руководство пользователя страница 114

Страница: 114 / 176

Agilent Technologies Helium Leak Detector

114

DRAFT 12

1/17

7.4.1 Software Update

Contact Agilent Customer Service/Technical Support for the latest software upgrade.

The software update utility is necessary when added features and software upgrades are
needed. A USB jump drive is all that is needed. The USB port is located in the back of the
leak detector Figure 7-2.

Figure 7-2 USB Port

1. Select the

Software Update

option.

You are prompted to insert the USB drive into the back of the leak detector (Figure 7-3).

Figure 7-3 Insert USB Drive

2. Inset the USB drive.

3. Select

Continue

The software update takes no more than 15 seconds.

4. Power off the leak detector as instructed and power back on.

5. Verify in the

System Information

Menu that the correct software was installed

Содержание G8610A

















































































































































































Результаты поиска

Содержание G8610A

Отзывы:

Бренды по названию

Популярные бренды

Agilent Technologies G8610A, Руководство по эксплуатации

Результаты поиска

Содержание G8610A

Отзывы:

Бренды по названию

Популярные бренды