manualshive.com logo in svg

Agilent Technologies G8610A, Руководство по эксплуатации

Поделиться
Скачать
Agilent Technologies G8610A Скачать руководство пользователя страница 132

Agilent Technologies Helium Leak Detector 

132

DRAFT 12

/1

1/17

Cleanliness is vital when servicing the leak detector or any vacuum equipment. There are 
some techniques more important in leak detector servicing than in general vacuum work:

CAUTION

Do not use silicone

 

oil or silicone grease.

Use powder-free butyl or polycarbonate gloves to prevent skin 
oils from getting on vacuum surfaces.

Do not clean any aluminum parts with Alconox

®

. Alconox is 

not compatible with aluminum and will cause damage.

NOTE

Agilent does not recommend the use of vacuum grease. 
Vacuum grease absorbs helium tracer gas and releases this 
slowly resulting in helium background during leak test 
operations. If it must be used, use it sparingly and avoid 
silicone types. Apiezon

®

 L grease is recommended (Agilent Part 

No. 695400004). 

When removing, checking or replacing O-rings:

CAUTION

Remove O-rings carefully with your fingers. Do not use metal 
tools for this task. This prevents scratching of any sealing 
surfaces.

Wipe all O-rings clean with a lint-free cloth before installation 
to ensure that no foreign matter is present to impair the seal.

Do not use grease or any other substances on O-rings or metal 
seals that will come in contact with the spectrometer.

Do not use alcohol, methanol or other solvents on O-rings as 
this causes deterioration and reduces their ability to hold a 
vacuum.

NOTE

If applicable, apply a small amount of Apiezon

L grease and 

wipe the O-rings shiny dry.

NOTE

Due to the effective cleaning nature of VacuSolv solvent and 
its residue-free properties, Agilent’ Component and 
Spectrometer Cleaning Kit (Part Number 670029096), used in 
accordance with the kit instructions, is recommended for 
cleaning spectrometer components. The kit can also be used for 
fine cleaning of other parts in the leak detector’s vacuum 
system such as valves and fittings. No rinsing steps or 
high-temperature drying are required following cleaning with 
VacuSolv. Although appropriate precautions are advised, 
VacuSolv is compatible with most materials and does not 
contain toxic chemicals or CFCs (chlorofluorocarbons). Other 
acceptable solvents are isopropyl alcohol (IPA) or Dow 
Corning

®

 OS-20.

Содержание G8610A

















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды