manualshive.com logo in svg

Agilent Technologies G8610A, Руководство по эксплуатации

Поделиться
Скачать
Agilent Technologies G8610A Скачать руководство пользователя страница 150

Agilent Technologies Helium Leak Detector 

150

 DRAFT 12

/1

1/17

DISABLE-xREJECT

Turns the Reject Set Point OFF. Where x is a number from 1 to 4 or the 
letter A.

DISABLE-RANGESTOP

Turns the Range Stop function OFF.

DISABLE-VOLUME

Turns audio OFF.

ENABLE-0ENABLE

Turns the Zero Enable function ON.

ENABLE-PASSWORD

Turns the Password feature ON.

ENABLE-xREJECT

Turns the Reject Set Point ON. Where x is a number from 1 to 4 or the 
letter A.

ENABLE-RANGESTOP

Turns the Range Stop function ON.

ENABLE-SEQUENCER

Turns the auto sequencer function ON.

ENABLE-SPLITFLOW

Turns the split flow function ON.

ENABLE-VOLUME

Turns audio ON.

EXTERNAL

Sets the External Calibrated Leak (in test port) as the leak for use during 
calibration.

INCREMENT

Adds 1 to the Manual Ranging leak rate exponent (making it less negative). 
Success is indicated by the normal 

ok

 response. Does nothing in 

auto-ranging mode. Does nothing upon reaching the least sensitive range.

INTERNAL

Sets the Internal Calibrated Leak as the leak to be used during calibration.

KEEP

Causes the leak detector to close most valves and enter the Hold state.

MANUAL

Turns the Manual Ranging Mode ON. Success is indicated by the normal 

ok

 response.

NOSNIFF

Turns the HIGH PRESSURE TEST function OFF.

ROUGH

Causes the leak detector to begin a roughing on the test port only.

SNIFF

Turns the HIGH PRESSURE TEST mode ON.

STDLEAK

Turns Read Std Leak ON/OFF. Verifies calibration by exposing internal cal 
leak to the system.

TPTCATM

Sets the current test port thermocouple reading to represent atmospheric 
pressure when the test port is exposed to atmosphere. Success is indicated 
by the normal 

ok

 response.

TPTCZERO

Sets the current test port thermocouple reading to represent a ZERO 
pressure reading when the test port pressure is less than 1.0E-04 Torr. 
Success is indicated by the normal 

ok

 response.

Table A-4  Leak Detection Actions (Continued)

Command

Action

Содержание G8610A

















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды