Agilent Technologies G8610A Скачать руководство пользователя страница 112

Страница: 112 / 176

Agilent Technologies Helium Leak Detector

112

DRAFT 12

1/17

NOTE

The password can also be read through the RS-232 port in the
event of a lost password. See Section A “Communications
Protocol” on page 139.

Lock Vent Control

Disables the

VENT

button. This option prevents accidental system

venting during test while under remote or PLC control. The

Vent

Lock

feature is not active when the

Auto Sequencer

is on.

Lock All Contro

Disables the

Test

Vent

and

Zero

buttons. This option prevents acci-

dental system venting, testing, system hold and Zeroing during test
while under remote or PLC control.

6.3 Wireless

❑

Information relating to wireless communications.

MAC Address

Two MAC addresses appear on this screen:

❑

The MAC address at the top of the screen is the leak detector
MAC address.

❑

The MAC address above the hand held button is the MAC
address of the hand held device.

SYNC Channel

For informational and factory debug purposes only.

SS ID

Displays the SS ID number, factory set to 086, for informational and
factory debug purposes only.

Channel

Click the button and a keypad appears to configure the channel
(1-19) that the unit uses to communicate with the wireless remote.
Up to 10 wireless remotes and leak detectors can be



communicating in a common area at a time.

Содержание G8610A

















































































































































































Результаты поиска

Содержание G8610A

Отзывы:

Бренды по названию

Популярные бренды

Agilent Technologies G8610A, Руководство по эксплуатации

Результаты поиска

Содержание G8610A

Отзывы:

Бренды по названию

Популярные бренды