Agilent Technologies G1888 Скачать руководство пользователя страница 159

Страница: 159 / 192

Maintaining the Instrument

User Information

159

Begin the calibration process.

Attach the K-type probes to the digital
thermometer

Press

Enter

on the Headspace Sampler

to continue.

Record temperature readings.

Allow 1 hour for the Headspace
Sampler to reach the setpoint shown.

Record the temperature shown on the
digital thermometer.

Press the down arrow key to move to
the next temperature setpoint. Repeat
until each setpoint has been recorded.

•

To repeat a measurement at a lower
setpoint, press the up arrow key
until the setpoint is displayed on
the screen. Open the lid of the oven
to allow cooling.

•

Record the temperature reading in

Table 20

Enter temperature measurements.

The Headspace Sampler displays a
table showing the temperature
setpoints. Use the keypad to enter the
measured values under each setpoint.

Press the down arrow to move to the
next setpoint. Repeat until each
measurement is entered.

Calculate offset.

After each of the 14 temperature
settings is entered, the HS asks
“Ready to process custom
temperature offset?”

Press

Enter

to complete. Press

Clear

to go back.

Table 22

Collect the temperature measurements

(continued)

Step

Action

Notes

medium_standard.book Page 159 Tuesday, February 17, 2004 10:14 AM

Содержание G1888

































































































































































































Результаты поиска

Содержание G1888

Отзывы:

Бренды по названию

Популярные бренды

Agilent Technologies G1888, Информация пользователя

Результаты поиска

Содержание G1888

Отзывы:

Бренды по названию

Популярные бренды