manualshive.com logo in svg

Agilent Technologies G1888, Информация пользователя

Поделиться
Скачать
Agilent Technologies G1888 Скачать руководство пользователя страница 149

Maintaining the Instrument

User Information

149

7

Disconnect the transfer line from the GC inlet. If a transfer 
line needle is used, plug off the end with a septa. If there is 
no needle, plug off the end with a union and plug.

8

Place an empty 20-mL capped vial in tray position 1. Make 
sure the Headspace Sampler is set for 20-mL vials. See 

page 80

.

9

Place the aluminum leak test vial in tray position 2. Place the 
end of the vial labeled “G1888” facing up.

10

Press the 

Menu

 key. Select 

Advanced Functions

. Choose 

menu item 18 

Leak Test

 and press 

Enter

. Press 

Enter

 

again to begin the test.

Running the restriction test

The Headspace Sampler loads the vial in tray position 1 into the 
oven carousel and raises it onto the sampling probe. The vial 
remains on the probe for the this part of the test.

1

The pressurization valve opens and pressurizes the vial for 
0.2 minutes. After 0.2 minutes, the pressurization valve 
closes. The vent valve opens for 0.3 minutes. The vented air 
flows through ports 1, 3, 5, and 6 of the sampling valve.

Watch the beaker of water. The valve clicks and bubbles 
emerge from the tube in the water. Normal behavior is a burst 
of bubbles that slows and stops after 4-5 seconds.

2

The pressurization valve opens and pressurizes the vial for 
0.2 minutes. After 0.2 minutes, the pressurization valve 
closes. The vent valve opens for 0.3 minutes. The vented air 
flows through ports 5 and 6 of the sampling valve.

The instrument switches the 6-port valve to the inject 
position. Watch the beaker of water. The valve clicks and 
bubbles emerge from the tube in the water. Normal behavior 
is a burst of bubbles that slows and stops after 3-4 seconds.

3

At the end of the restriction test, the instrument returns the 
empty glass vial to tray position 1. The Headspace Sampler 
sets the valves in standby mode and loads the aluminum leak 
test vial from tray position 2.

medium_standard.book  Page 149  Tuesday, February 17, 2004  10:14 AM

Содержание G1888

































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды