Agilent Technologies E1364A Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 76

background image

Chapter 2

Configuring the Agilent E1364A Form C

Switch

Using This Chapter

This chapter shows how to make user connections to the Form C Switch and
how to configure the switch module. Chapter contents are:

•

Warnings and Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 17

•

Connecting User Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 18

•

Typical Switch Configurations . . . . . . . . . . . . . . . . . . . . . . . Page 20

•

Changing Form C Switch Components . . . . . . . . . . . . . . . . . Page 23

•

Module Front Panel Connections. . . . . . . . . . . . . . . . . . . . . . Page 24

Warnings and Cautions

Warning

SHOCK HAZARD. Only qualified, service-trained personnel who
are aware of the hazards involved should install, configure, or
remove the module. Use wire rated for the highest input voltage
and remove all power sources from the mainframe and installed
modules before installing or removing a module.

Caution

MAXIMUM VOLTAGE/CURRENT. Maximum allowable voltage per
channel for the module is 250 Vdc or 250 Vac RMS (350 V ac peak).
Maximum current per channel is 1 Adc or 1 Aac RMS (non-inductive).
Maximum power input is 40 W (dc) or 40 VA (ac) per channel or 320 W
(dc) or 320 VA (ac) per module. Exceeding any limit may damage the
module.

Caution

CONN 5V + 12V: On the module, the bac 5V line is
fused at 4 A and the + 12V line at 1 A. When conn 5V or + 12V to
the Form C Switch, install appropriate pullup resistors to prevent shorting
the power supplies. Also, the total current drawn by all circuits connected to
the Form C Switch must not exceed the fuse rating for the supplies used.

Chapter 2

Configuring the Agilent E1364A Form C Switch 17

«
...
17
18
19
20
21
...
»

Содержание E1364A













































































Отзывы:

Нет отзывов

Похожие инструкции для E1364A

Бренд: Valcom Страницы: 2

Celabs Distribution Hub and Receiver

Бренд: Cable Electronics Страницы: 2

Бренд: König Страницы: 8

Бренд: Atlantis Land Страницы: 3

MCD-LED17 series

Бренд: Raritan Страницы: 89

Бренд: Avenview Страницы: 10

Бренд: GeoVision Страницы: 7

Бренд: Black Box Страницы: 2

Бренд: Accton Technology Страницы: 7

Бренд: Edimax Страницы: 2

Summit X450-G2-24t-GE4

Бренд: Extreme Networks Страницы: 2

Бренд: N-Tron Страницы: 2

Бренд: StarTech.com Страницы: 12

Бренд: Datavideo Страницы: 90

UniServer BX720EF

Бренд: H3C Страницы: 46

UniServer BX1010E

Бренд: H3C Страницы: 48

UniServer BX608FE

Бренд: H3C Страницы: 11

Бренд: W&T Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды