Agilent Technologies E1364A Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 76

background image

OPEN?

[ROUTe:]OPEN? <channel_list>

returns the current state of the channel(s)

queried. channel_list has the form (@ccnn) (see [ROUTe:]OPEN for
definition). The command returns 1 if channel(s) are open or returns 0 if
channel(s) are closed.

Comments

•

Query is Software Readback: The ROUTe:OPEN? command
returns the current software state of the channels specified. It does
not account for relay hardware failures. A maximum of 127 channels
at a time can be queried for a multi-module switchbox.

Example

Query Channel Open State:
This example opens channels 100 and 213 of a two-module switchbox and
queries channel 213 state. Since channel 213 is programmed to be open, 1 is
returned.

OPEN (@100,213)

Open channels 100 end 213

OPEN? (@213)

Query channel 213 state

SCAN

[ROUTe:]SCAN <channel_list>

defines the channels to be scanned.

channel_list has the form (@ccnn) where cc = card number (01-99) and nn
= channel number (00-15).

Parameters

Parameter Name

Parameter Type

Range of Values

<channel_list>

numeric

cc00 - cc15

Comments

•

Defining Scan List: When [ROUTe:]SCAN is executed, the channel
list is checked for valid card and channel numbers. An error is
generated for an invalid channel list.

•

Scanning Channels: You can scan single channels (@ccnn);
multiple channels (@ccnn,ccnn,...); sequential channels
(@ccnn:ccnn); groups of sequential channels
(@ccnn:ccnn,ccnn:ccnn); or any combination.

•

Scanning Operation: When a valid channel list is defined,
INITiate[:IMMediate] begins the scan and closes the first channel in
the channel list. Successive triggers from the source specified by
TRIGger:SOURce advance the scan through the channel list.

•

Stopping Scan: See ABORt.

•

Related Commands: TRIGger, TRIGger:SOURce

•

*RST Condition: All channels open.

Example

Scanning Using External Device:
See Chapter 4, "Example: Scanning With External Devices" or "Example:
Scanning Using Trig Out and Event In Ports" for example scanning
programs using external instruments.

54 Agilent E1364A Form C Switch Command Reference

Chapter 5

«
...
54
55
56
57
58
...
»

Содержание E1364A













































































Отзывы:

Нет отзывов

Похожие инструкции для E1364A

Бренд: Xantech Страницы: 2

Бренд: ifs Страницы: 352

M800 Elite Series

Бренд: 4B Страницы: 12

Бренд: Silent Gliss Страницы: 4

Бренд: N-Tron Страницы: 132

Бренд: Imtex-Controls Страницы: 2

Бренд: I-Tech Страницы: 39

PMV WM Ultraswitch

Бренд: Flowserve Страницы: 16

Бренд: Extron electronics Страницы: 3

Бренд: Accton Technology Страницы: 7

Бренд: ATEN Страницы: 2

Бренд: Pulse-Eight Страницы: 9

Бренд: Black Box Страницы: 2

Бренд: NewStar Страницы: 10

CheetaHub Classic-2041

Бренд: Accton Technology Страницы: 7

Бренд: Nxg Страницы: 2

Бренд: IPGARD Страницы: 2

Бренд: Lindy Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды