Agilent Technologies 83236B Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 164

Agilent Technologies 83236B Скачать руководство пользователя страница 4

iv

Certification

Agilent Technologies certifies that this product met its published specifications at
the time of shipment from the factory. Agilent Technologies further certifies that
its calibration measurements are traceable to the United States National Institute of
Standards and Technology, to the extent allowed by the Institution's calibration
facility, or to the calibration facilities of other International Standards Organization
members.

Warranty

This Agilent Technologies instrument product is warranted against defects in
material and workmanship for a period of one year from the date of shipment,
except that in the case of certain components listed in Specifications of this manual,
the warranty shall be for the specified period. During the warranty period, Agilent
Technologies will, at its option, either repair or replace products which prove to be
defective.

For warranty service or repair, this product must be returned to a service facility
designated by Agilent Technologies. Buyer shall prepay shipping charges to
Agilent Technologies and Agilent Technologies shall pay shipping charges to
return the product to Buyer. However, Buyer shall pay all shipping charges, duties,
and taxes for products returned to Agilent Technologies from another country.

Agilent Technologies warrants that its software and firmware designated by
Agilent Technologies for use with an instrument will execute its programming
instruction when properly installed on that instrument. Agilent Technologies does
not warrant that the operation of the instrument, or software, or firmware will be
uninterrupted or error free.

Limitation Of
Warranty

The foregoing warranty shall not apply to defects resulting from improper or
inadequate maintenance by Buyer, Buyer-supplied software or interfacing,
unauthorized modification or misuse, operation outside of the environmental
specifications for the product, or improper site preparation or maintenance.

No

other warranty is expressed or implied. Agilent Technologies specifically
disclaims the implied warranties of merchantability and fitness for a particular
purpose.

Exclusive
Remedies

The remedies provided herein are buyer's sole and exclusive remedies. Agilent
Technologies shall not be liable for any direct, indirect, special, incidental, or
consequential damages, whether based on contract, tort, or any other legal theory.

Assistance

Product maintenance agreements and other customer assistance agreements are
available for Agilent Technologies products.

For any assistance, contact your nearest Agilent Technologies Sales and Service
Office. Addresses are provided at the back of this manual.

«
...
2
3
4
5
6
...
»

Содержание 83236B





































































































































































Отзывы:

Нет отзывов