manualshive.com logo in svg

Agilent Technologies 708-DS, Руководство оператора

Поделиться
Скачать
Agilent Technologies 708-DS Скачать руководство пользователя страница 110

110

708-DS / 709-DS Operator’s Manual

4

Operating the 708-DS / 709-DS

 

Timepoint Overlap Error

The Timepoint Overlap error screen displays when the time point start 
times entered do not provide sufficient time for all operations to perform 
before the next time point is due. This error typically occurs when the 
manifold lead time plus the manifold down time exceeds the time point 
interval. See 

“Method Properties Screen 4”

on page 74 to correct the 

overlap. Press 

Ok

 to clear the error.

Pause Duration Exceeded

The Alarm error screen displays when the pause duration alarm time has 
been exceeded (

“Menu Screen - Alarms”

on page 80). Press 

Ok

 to clear 

the dialog.

Vessel Temperature Error

Displays when a vessel temperature has exceeded the allowable 
tolerance range (

“Menu Screen - Instrument Settings Screen 2”

on 

page 84). The vessel temperatures are displayed in blue if they are 
within tolerance. They are red if they are outside the allowed tolerance 
range. Press 

Ok

 to continue the run.

Bath Temperature Error

The Temperature Error screen displays when the bath temperature has 
exceeded the allowable tolerance range (

“Menu Screen - Instrument 

Settings Screen 2”

on page 84). Press 

Stop

 to abort the current method 

and return to the Main screen. Press 

Ok

 to continue the run.

Table 17

Error Screens (Red)

Содержание 708-DS













































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды