manualshive.com logo in svg

Agilent Technologies 708-DS, Руководство оператора

Поделиться
Скачать
Agilent Technologies 708-DS Скачать руководство пользователя страница 107

Operating the 708-DS / 709-DS

4

708-DS / 709-DS Operator’s Manual

107

 

Out of Paper Notification

This warning is applicable to systems with a printer installed. This 
warning does not interrupt a running method. If the printer runs out of 
paper during a run (

“Printer Maintenance”

on page 127), the results may 

be printed out by selecting 

Menu 

>

 Reports 

> 

Last Run Results 

(

“Menu Screen - Reports”

on page 77). Press 

Ok

 to clear the warning. 

Automated Drive Unit Movement Warning

Applies to systems with automated drive units. It indicates that you must 
move the drive unit to its lowest position to continue a run. Press 

Ok

 to 

lower the drive unit to its lowest position. Press 

Cancel

 to abort the 

current method and return to the Main screen.

Temperature Probe Open Warning

Indicates that one or more temperature probes have failed. A red X is 
placed in the appropriate space indicating which probe(s) have failed. 

Note: 

The unit may require service. Refer to the 

Agilent 708-DS / 

709-DS Service Manual

 for troubleshooting.

Press 

Retry

 to re-test the probes. Press 

Ignore

 to clear the warning. 

Table 16

Warning Screens (Yellow)

Содержание 708-DS













































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды