manualshive.com logo in svg

Agilent Technologies 708-DS, Руководство оператора

Поделиться
Скачать
Agilent Technologies 708-DS Скачать руководство пользователя страница 106

106

708-DS / 709-DS Operator’s Manual

4

Operating the 708-DS / 709-DS

 

Instantaneous Spindle Speed Jump

If the spindle speed varies by more than 2% over a 40-msec interval, the 
Spindle Speed Warning screen displays.

Caution (Stop): The most common cause of this error is a shaft being 
held while performing diagnostics. 

Press 

Ok

 to return to the Diagnostics screen.

Preheating Notification

This warning displays during preheating for Vessel or Bath selected start 
options. The warning changes to reflect the current configuration of the 
system. Current bath or vessel temperatures are displayed during 
preheating. Press 

Cancel

 to abort the run and return to the Main screen.

Alarm Time Expired

Displays when the Timer Alarm has expired (

“Main Screen - 

Alarms”

on page 65). Press 

Ok

 to clear the warning.

Table 16

Warning Screens (Yellow)

Содержание 708-DS













































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды