Agilent Technologies 708-DS Скачать руководство пользователя страница 80

Страница: 80 / 140

708-DS / 709-DS Operator’s Manual

Operating the 708-DS / 709-DS

Menu Screen - Alarms

Two different alarms are available through the Alarms screen:

Table 5

Menu Screen - Alarms

Alarm

Function

Timer

This alarm functions as a countdown timer. Enter the duration as
HH:MM:SS. Press

to start the timer. When the alarm duration

expires, the Alarm Time Expired warning displays (

“Alarm Time

Expired”

on page 106) and an audible alarm sounds. This alarm sounds

until you press

. To cancel a previously running alarm before time

has expired, enter 0 for the Timer Alarm value.

Pause Duration

This field allows you to set the maximum pause period while running a
method. When a running method is paused, a timer starts. If the pause
time exceeds this Pause Duration, the Pause Duration Exceeded error
displays (

“Pause Duration Exceeded”

on page 110), an alarm sounds,

and a message is sent to the printer. Entering a zero in this field disables
the Pause Duration Alarm.

Содержание 708-DS













































































































































Результаты поиска

Содержание 708-DS

Отзывы:

Бренды по названию

Популярные бренды

Agilent Technologies 708-DS, Руководство оператора

Результаты поиска

Содержание 708-DS

Отзывы:

Бренды по названию

Популярные бренды