manualshive.com logo in svg

Agilent Technologies 16712A, Руководство пользователя

Поделиться
Скачать
Agilent Technologies 16712A Скачать руководство пользователя страница 107

106

Chapter 1: Agilent Technologies 16712A 128K Sample Logic Analyzer

Specifications and Characteristics

  - Channel-to-Channel Skew:    2 ns, typical for 1-card module
                                2.5 ns, typical for 2-card module

Triggering
  - Sequencer Speed:                 125 MHz, maximum
  - State Sequence Levels:           12
  - Timing Sequence Levels:          10
  - Maximum Occurrence Count Value:  1,048,575
  - Pattern Recognizers:             10
  - Range Recognizers:               2
  - Range Width:                     32 bits each
  - Timers:                          2
  - Timer Value Range:               400 ns to 500 seconds
  - Glitch/Edge Recognizers:         2 (timing only)
  - Minimum Detectable Glitch:       3.5 ns

Power Requirements
  All necessary power is supplied through the backplane connector
  of the logic analysis system mainframe.

Operating Environment Characteristics
  - Indoor use only.
  - Temperature
    Instrument (except disk and media): 0 to 50 degrees C (+32
                                        to 122 degrees F) in 16700A
                                        0 to 40 degrees C (+32
                                        to 104 degrees F) in 16600A-series
    Probe lead sets and cables:         0 to 65 degrees C (+32 to
                                        149 degrees F)
  - Humidity
    Instrument, probe lead sets, and cables: up to 95% relative humidity at
                                             40 degrees C (+104 degrees F)
  - Altitude      To 4600 m (15,000 ft)
  - Vibration
    Operating:    Random vibration 5 to 500 Hz, 10 minutes per axis,
                  approximately 0.3 g (rms)
    Nonoperating: Random vibration 5 to 500 Hz, 10 minutes per axis,
                  approximately 2.41 g (rms); and swept sine resonant
                  search, 5 to 500 Hz, 0.75 g (0-peak), 5-minute
                  resonant dwell at 4 resonances per axis.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание 16712A
























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды