AEM Performance Electronics CD-5 Carbon Скачать руководство пользователя

Страница: 63 / 120

AEMNet Network Wiring

Refer to the following guidelines when wiring AEMnet (CAN) devices.

Twisted wire is required with >1 twist per inch.

AEMnet buses must be properly terminated. Termination resistors are 120 Ohms each, two total, located at the
physical ends of the bus wires.

Termination Resistors

Device

Configuration

30-2226, 6ch CAN Sensor Module

No resistor

30-2224, CAN EGT

No resistor

30-2212, 22ch CAN Sensor Module

Jumper selectable

30-560X & 30-570X CAN Dash

Software selectable, enabled by default

30-710X, Infinity

Hardware enabled by default on CAN A
(AEMNet)

30-2500, AQ1

Included, non-configurable

The following Deutsch DTM 4-pin termination plugs are available

Description

35-3440-F

AEMNet Termination Plug, Female

35-3440-M

AEMNet Termination Plug, Male

Example Network Configurations

Example Network Configurations
Note:

These diagrams assume that there are no other devices on the network

Содержание CD-5 Carbon

























































































































Результаты поиска

Содержание CD-5 Carbon

Отзывы:

Похожие инструкции для CD-5 Carbon

Бренды по названию

Популярные бренды

AEM Performance Electronics CD-5 Carbon, Руководство пользователя

Результаты поиска

Содержание CD-5 Carbon

Отзывы:

Похожие инструкции для CD-5 Carbon

Бренды по названию

Популярные бренды