AEM Performance Electronics CD-5 Carbon Скачать руководство пользователя | Manualshive

Страница: 56 / 120

background image

56

Jumper Configuration

Two configuration jumpers are located inside the enclosure of the Module. The cover may be removed by
unscrewing the four external screws to change the jumper positions if needed. The Module is delivered from the
factory in the most common configuration suitable for use with AEMnet (and other) devices; changing the jumper
positions is not typically necessary.

CAN CFG -

The default position of 500 kb/s & 29 bit ID is correct for AEMnet. Please refer to the manufacturer's

documentation if you are using any third-party devices.

UNIT ID -

The default position is correct if there is only a single AEM K-Type CAN Module installed on your network.

If you are using two Modules, the first unit must be set to 'UNIT 1' and the second to 'UNIT 2'.

No Jumper

1 - 2

2 - 3

Description

UNIT ID

UNIT 2

UNIT 1*

First or Second Unit on Bus

CAN CFG

250 kb/s

11-bit ID

500 kb/s*

29-bit ID

1000 kb/s

29-bit ID

Bus Speed / ID Type

Jumper Position ( * = Default Position)

«
...
54
55
56
57
58
...
»

Содержание CD-5 Carbon

























































































































Отзывы:

Нет отзывов

Похожие инструкции для CD-5 Carbon

Бренд: Samsung Страницы: 2

scx-4100 series

Бренд: Samsung Страницы: 8

Бренд: Darfon Страницы: 28

Бренд: VanEssa mobilcamping Страницы: 8

Бренд: FEIYUTECH Страницы: 8

Бренд: FeiYu Tech Страницы: 2

Бренд: FeiYu Tech Страницы: 2

Бренд: FEIYUTECH Страницы: 26

Бренд: wattio Страницы: 15

Бренд: LAUMAS Страницы: 44

AERASGARD RCO2-W

Бренд: S+S Regeltechnik Страницы: 32

Бренд: Sanitas Страницы: 52

Бренд: T-Home Страницы: 52

Бренд: Porsche Страницы: 192

Бренд: Atlas Copco Страницы: 88

Бренд: Chevrolet Страницы: 356

Бренд: Ford Страницы: 272

Бренд: Pontiac Страницы: 376

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды