AEM Performance Electronics CD-5 Carbon Скачать руководство пользователя | Manualshive

Страница: 40 / 120

background image

40

Electrical

The supplied 36-2212 harness comes with a pre-terminated AEMnet spur suitable for powering the module and
providing AEMnet/CAN connectivity.  In addition, pre-terminated lengths of various color wire are supplied for
connection to sensors.  The harness connector is a multi-piece assembly which has a clear plastic retainer that
must be removed prior to inserting the crimped leads into the assembly.  Please see instructions later in this
manual.

Sensor Wiring

·

The Sensor Module should only be powered through the dedicated power and power ground pins,

*not*

sensor

ground

·

Every connected sensor should be connected to one of the dedicated

sensor

ground pins to ensure accurate

readings

·

Do not connect the Module's 5V sensor power to anything

other than

dedicated sensors that require 5V power,

e.g. pressure sensors

·

Route wiring away from sources of noise such as alternators, ignition components, or other high power/frequency
wiring

·

Shielded wire is suggested to reduce the susceptibility of noise; the shield should only be grounded/drained on
one end of the wiring harness

·

CAN wiring should utilized twisted pairs (> 1 TPI); shielding is recommended

·

This module is

not

compatible with K-type thermocouples

(unless a K-type amplifier is used)

; RTD-style EGT

sensors

are

compatible, e.g. AEM PN 30-2050

·

The Sensor Module's sensor ground should be at the same level as the sensor ground of any "tapped" sensors,
i.e. existing/OEM sensors that are connected to an external ECU/device

·

The device pinout section includes a Suggested Interface column. This may make integration with an
AEM Dash easier as sample layouts will be provided that follow these guidelines.

«
...
38
39
40
41
42
...
»

Содержание CD-5 Carbon

























































































































Отзывы:

Нет отзывов

Похожие инструкции для CD-5 Carbon

Бренд: Gates Страницы: 26

Бренд: Free Spirits Страницы: 32

Бренд: IHP Страницы: 8

Бренд: CAB Страницы: 21

Бренд: PASCO Страницы: 5

Бренд: PASCO Страницы: 4

Бренд: PASCO Страницы: 8

Бренд: PASCO Страницы: 4

Бренд: PASCO Страницы: 12

Бренд: PASCO Страницы: 5

Бренд: PASCO Страницы: 3

Бренд: Fabbri Страницы: 4

Бренд: Smartech Страницы: 8

Бренд: FABBRI PORTATUTTO Страницы: 2

Бренд: Ford Страницы: 2

Бренд: Cycling Sports Group Страницы: 8

Бренд: PSF Страницы: 2

Бренд: IKAR Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды