AEM Performance Electronics CD-5 Carbon Скачать руководство пользователя | Manualshive

Страница: 36 / 120

background image

36

Specifications

Dimensions

width

2.1 / 55

in / mm

length

2.1 / 55

in / mm

height

1.3 / 34

in / mm

mass

1.2 / 32

oz / g

Supply Voltage

min

7

VDC

max

18

VDC

Supply Current (13.8V)

nominal

165

mA

Operating Temperature

min

-4 / -20

degF / degC

max (16V Supply)

185 / 85

degF / degC

5V Sensor Supply

Current

250

mA

Analog Inputs 1 - 2

Range

0 - 65535

Ohm

Resolution

1 (12-bit)

Ohm

Pull-up (5V)

2,200

Ohm

CAN Transmit Rate

100

Hz

Analog Inputs 3 - 4

Range

0 - 5

VDC

Resolution

0.001 (12-bit)

VDC

Pull-up (5V)

100,000

Ohm

CAN Transmit Rate

100

Hz

Fuel Level Input

Range

0 - 250

Ohm

Resolution

1 (12-bit)

Ohm

Pull-up

5

VDC

CAN Transmit Rate

50

Hz

Tachometer Input

Range

0 - 1500

Hz

Resolution

1

Hz

Pull-up

12

VDC

Minimum Trigger Voltage

3

VDC

Maximum Voltage (Sustained)

18

VDC

CAN Transmit Rate

50

Hz

FAQ / Troubleshooting

My CAN Sensor Module doesn't seem to be outputting anything.

Confirm that your CAN bus is properly terminated and that all nodes are configured for the right bus speed. In
addition, any receiving devices/nodes must be specifically configured to receive as the Module is configured to
transmit; specifically, the CAN ID, bus speed, and number of ID bits.

Can I use the CAN Sensor Module with my AEM AQ-1, AEM CAN Gauge, or AEM ECU?

No, the CAN Sensor Module is only compatible with the CD-series dash displays and other third-party devices at
this time.

Where can I find AEM .dbc files?

AEM dbc files are available via the AEM Forum and within the AEM CD-series dash display software installer.
Please visit

www.aemelectronics.com

for more information and downloads.

Can I connect more than one 6 Channel CAN Sensor Module on one CAN bus?

No, this is not possible. Please use the AEM 22 Channel CAN Sensor Module if you need more inputs.

For support, contact AEM Technical Support at 1-800-423-0046 or

[email protected]

.

«
...
34
35
36
37
38
...
»

Содержание CD-5 Carbon

























































































































Отзывы:

Нет отзывов

Похожие инструкции для CD-5 Carbon

Two-Knife Booklet Trimmer-A1

Бренд: Canon Страницы: 32

Perfect Binder-C1

Бренд: Oce Страницы: 82

Бренд: Panasonic Страницы: 443

Бренд: cam Страницы: 28

Бренд: quadient Страницы: 2

AcousticDesign AD-S52

Бренд: QSC Страницы: 4

Бренд: X10 Страницы: 1

Бренд: Oki Страницы: 20

Бренд: 3SIXT Страницы: 12

Бренд: Anslut Страницы: 12

Бренд: Kia Страницы: 54

Бренд: Metra Electronics Страницы: 2

Бренд: Southern Enterprises Страницы: 4

Бренд: Ohlins Страницы: 8

Бренд: LINHOF Страницы: 5

Бренд: Levana Страницы: 14

Бренд: Ikelite Страницы: 28

Бренд: Chicco Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды