AEM Performance Electronics CD-5 Carbon Скачать руководство пользователя | Manualshive

Страница: 54 / 120

background image

54

Unit 1:

0x507(11) / 0x0000B007 (29) at 50Hz

Unit 2:

0x607(11) / 0x0000C007 (29) at

25Hz

Byte

Label

Data Type

Scaling

Offset

Range

0

Digital5Frequency

16 bit unsigned

1 Hz/bit

0

0 to 65535 Hz

1

2

Digital6Frequency

16 bit unsigned

1 Hz/bit

0

0 to 65535 Hz

3

6

Digital5DutyCycle

8 bit unsigned

1 %/bit

0

0 to 255 %

7

Digital6DutyCycle

8 bit unsigned

1 %/bit

0

0 to 255 %

6

Digital5State

8 bit unsigned

1

0

0 to 255

7

Digital6State

8 bit unsigned

1

0

0 to 255

8 Channel K-Type CAN Module to Dash

Kit Contents

The AEM 8 Channel K-Type CAN Module enables a user to put eight K-type thermocouples on to an AEMnet or
CAN bus.  K-type thermocouples are suitable for various applications such as exhaust gas temperature (EGT)
measurement, pre/post intercooler temperatures, cylinder head temperatures, and more.  All measurements are cold
junction compensated with a range of -200 to +1372 degC / -328 to +2501 degF.  The Module is provided with a four-
pin DTM connector to provide CAN, power connectivity, and eight miniature style K-type sockets.  The Module
supports the Bosch CAN 2.0b standard with flexible CAN configuration jumpers making it compatible with many
third-party devices.  Note: The only AEMnet devices that are compatible with the CAN Sensor Module are the CD-
series dash displays and AEM AQ-1 Data Logger.

Features

·

Eight (8) K-Type Cold Junction Compensated
Thermocouple Inputs

·

AEMnet/CAN Output (Thermocouple and Cold
Junction Temperatures)

·

-200 to +1372 degC / -328 to +2501 degF

·

±0.15% (Max) Thermocouple Full-Scale Error

·

0.1 degC Resolution

·

Open Circuit / Fault Detection

·

'Miniature' Style Thermocouple Sockets

·

Jumper selectable CAN bus speeds: 250k, 500k,
1M

·

Jumper selectable header length, 11 bit or 29 bit

·

Jumper selectable base address, two units can be
on the same bus

PN

QTY

Description

35-2224

1

MODULE, CAN K-TYPE MODULE

10-2224

1

INST, 30-2224

4-4083

1

2.0" x 1.5" VELCRO

35-2624

1

4 WAY DTM PLUG KIT

Installation

Mounting

The Module should may be mounted within the vehicle using the supplied hook-and-loop fastener or cable ties. The
Module's circuit board has a water-resistance coating applied and thus has some tolerance to a humid or
condensing atmosphere, however the thermocouple connectors are

not

sealed so a dry and cool mounting location

should be chosen.

Power / AEMnet (CAN)

A four pin Deutsch DTM receptacle is integrated into the Module's enclosure to provides power and AEMnet/CAN
connectivity. This allows a straightforward "Plug and Play" installation when adding to an existing AEMnet network.

«
...
52
53
54
55
56
...
»

Содержание CD-5 Carbon

























































































































Отзывы:

Нет отзывов

Похожие инструкции для CD-5 Carbon

Бренд: Lancia Страницы: 191

SuperStack 3 4300

Бренд: 3Com Страницы: 8

Бренд: 3B Medical Страницы: 7

Бренд: Metra Electronics Страницы: 14

Speedglas G5-02

Бренд: 3M Страницы: 17

Speedglas 9100 MP

Бренд: 3M Страницы: 72

Speedglas 9100-Air

Бренд: 3M Страницы: 63

Бренд: 3M Страницы: 84

Бренд: Karma Страницы: 7

Бренд: Jeep Страницы: 603

Бренд: Jeep Страницы: 80

Resusci Baby QCPR

Бренд: laerdal Страницы: 8

Бренд: quadient Страницы: 2

AcousticDesign AD-S52

Бренд: QSC Страницы: 4

Бренд: Paradyne Страницы: 4

Video 75 Plus Studio

Бренд: Sachtler Страницы: 34

Energy Hub EH128L

Бренд: TBB power Страницы: 24

10-8002-C11998B

Бренд: Saleen Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды