AEM Performance Electronics CD-5 Carbon Скачать руководство пользователя | Manualshive

Страница: 25 / 120

background image

25

Installation

Mechanical

The Sensor Module may be mounted within the vehicle using hook-and-loop
fastener (not included) or bolted (#4 screws included) to a suitable structure; a
mounting/drill diagram is provided below. The module is weather-resistant
(IP67) but is preferably mounted in a cool, dry area such as the driver
compartment.

Sensor Wiring

·

The Sensor Module should only be powered through the dedicated power and power ground pins,

*not*

sensor

ground

·

Every connected sensor should be connected to the dedicated

sensor

ground pins to ensure accurate readings

·

Do not connect the Module's 5V sensor power to anything

other than

dedicated sensors that require 5V power,

e.g. pressure sensors

·

Route wiring away from sources of noise such as alternators, ignition components, or other high power/frequency
wiring

·

Shielded wire is suggested to reduce the susceptibility of noise; the shield should only be grounded/drained on
one end of the wiring harness

·

CAN wiring should utilized twisted pairs (> 1 TPI); shielding is recommended

·

The Sensor Module's sensor ground should be at the same level as the sensor ground of any "tapped" sensors,
i.e. existing/OEM sensors that are connected to an external ECU/device

·

The device pinout section includes a Suggested Interface column. This may make integration with an
AEM Dash easier as sample layouts will be provided that follow these guidelines.

Quick Setup with AEM Dash

Be sure to install the latest version of the AEM DashDesign software.

Follow this

Software Download

link directly or follow the graphical instructions below.

The website will always contain the latest release version of DashDesign software. Your version number may be
different than the example above.

Once installed, you will find a library of setup files in your \Documents\AEM\DashDesign directory.  In the
\Documents\AEM\DashDesign\Setups\App Specific\AEM 30-2226 6 Ch CAN Sensor Module folder you will find all
currently available setup files for your 30-2226 6 Channel CAN Sensor Module.  They have a ".aemcd7" extension.
The file name describes each one.

A quick primer on basic setup modifications

«
...
23
24
25
26
27
...
»

Содержание CD-5 Carbon

























































































































Отзывы:

Нет отзывов

Похожие инструкции для CD-5 Carbon

Бренд: Panasonic Страницы: 252

Бренд: babymoov Страницы: 12

Бренд: BabyOno Страницы: 24

Бренд: babymoov Страницы: 4

Бренд: madebyzen Страницы: 16

Бренд: Quintex Страницы: 29

Бренд: Oki Страницы: 2

Бренд: OKIDATA Страницы: 16

GTM 10 - TMC Module

Бренд: Garmin Страницы: 1

Бренд: ZEPP Страницы: 36

FleetMaster Air FW8 Series

Бренд: SAF-HOLLAND Страницы: 20

Бренд: Hussmann Страницы: 10

Бренд: DEFA Страницы: 9

Slim Line LED Light Grille Kit

Бренд: rough country Страницы: 8

USB 3.0 Dual Head Docking Station

Бренд: SIIG Страницы: 12

Бренд: Thunderbike Страницы: 11

Monarch Pass M321

Бренд: Wolfman Страницы: 5

Бренд: HHD Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды