Advanced Energy THYRO-AX, Руководство пользователя

Страница: 81 / 117

46 47
The output value of the voltage
transformer is 10V~ (at rated voltage)
and the output value of the current
transformer is 1V~ (at rated current).
The corresponding load resistor has to
be connected externally as well.
6.7 DISPLAY VIA ANALOG OUTPUT
The following variables are given at the analog output (e.g. when con-
necting an external measurement instrument):
• load current (highest phase current from L1, L2, L3)
• load voltage (highest conductor voltage)
• effective power (overall power) (only in the case of ...H RLP2)
• additional variables (can be selected via PC/Bus, e.g. mains voltage,
setpoint etc.)
The variable to be given at the analog output can be configured by the
user (see chapter control mode/analog output).
DEFAULT SETTINGS
ANALOG OUTPUT OUTPUT VARIABLE
Analog output 1 load voltage
Analog output 2 load current
Analog output 3 power on the load
6.8 FAULT, STATUS AND MONITORING MESSAGES
The Thyro-AX has internal fault, status and user-defined monitoring mes-
sages. Their effects can be configured with the Thyro-Tool AX software.
The reactions on the occurrence of a message( =event) can be deter-
mined by the user. As a reaction, the inhibition of the load current (pulse
inhibition), as well as the display at the fault signaling relay K1 and the
color of the display lights (red) can be configured as well as the data log-
ger and the multi-I/O outputs
(s. chapter 6.8.1). Besides this the mode of
operation (open or closed circuit principle) can be configured at the fault
signaling relay K1. Fundamental fault messages which make the operation
of the device impossible in general switch the pulse inhibition or the fault
signaling relay K1.
yϮϮ͘ϭϬ
hĞdžƚ
yϮϮ͘ϭϭ
EĞƚnjͬ>ĂƐƚ
E
<
>
ů
Ŭ
yϮϮ͘ϭϮ
yϮϮ͘ϭϯ
/Ğdžƚ
EĞƚnj
>ĂƐƚ
Mains/Load
Mains
Load
DESCRIPTION THYRO-TOOL AX MESSAGE ON DISPLAY RELAY** PULSE INHIBIT DATA
OF FAULT MESSAGE DISPLAY LIGHTING ROT LOGGER
NETWORK IST NOT OK SYNC ERROR SYNC ERROR X X X* X
(SYNC ERROR)
HARDWARE ERROR HARDWARE FAULT HW FAULT X X X* X
MINIMUM FREQUENCY FREQUENCY TO LOW FMIN X X X* X
MAXIMUM FREQUENCY FREQUENCY TO HIGH FMAX X X X* X
VALID FREQUENCY FREQUENCY FTOLERANCE X X X* X
TOLERANCE TOLERANCE EXCEEDED
NO ROTATING FIELD/ NO ROTATING FIELD NO ROTFIELD X X X* X
LEFT ROTATING FIELD (FOR AX)
PHASE L1 IS MISSING PHASE L1 MISSING NO PHASE1 X X X* X
PHASE L2 IS MISSING PHASE L2 MISSING NO PHASE2 X X X* X
PHASE L3 IS MISSING PHASE L3 MISSING NO PHASE3 X X X* X
SETPOINT FAILURE SETPOINT < 4 mA SETPOINT X X X X
(SETPOINT < 4 mA) (OPEN LOOP)
NO SUPPLY VOLTAGE NO SUPPLY VOLTAGE NO POWER X X X* X
CONNECTION OF POWER UNIT NOCONNPART X X X* X
POWER UNITS DISCONNECTED
FAILURE OF TEMPERATURE TEMPERATURE TEMPSENS X X X X
SENSOR PROBE DEFECT
FUSE FAILURE OPEN FUSE FUSE X X X* X
THYRISTOR SHORT CIRCUIT THYRISTOR SHORT THYRISTOR X X X* X
CIRCUIT
EEPROM ERROR MEMORY ERROR EEPROM X X X*
I2C ERROR I2C ERROR I2C X X
ETHERNET ERROR ETHERNET ERROR ETH
USB ERROR USB ERROR USB
FIRMWARE ERROR FIRMWARE ERROR FIRMWARE X X X* X
POWER UNIT IS TOO SMALL POWER UNIT INCOMPPART X X X
FOR TYPE INCOMPATIBLE
U-MEASURING RANGE U MEASURING U RANGE X X
IS EXCEEDED RANGE EXCEEDED
U-MEASURING RANGE I MEASURING I RANGE X X
IS EXCEEDED RANGE EXCEEDED
NEGATIVE POWER NEGATIVE POWER NEG POWER X X
LCD ERROR LCD ERROR LCD X
PARAMETER ERROR PARAMETER ERROR PARAMETER X X* X
* = cannot be deactivated ** = default setting of fault signaling relay K1: closed circuit principle
6.8.1 OVERVIEW
The following table indicates the various messages (events) and their
specific classification of default settings (X).
TAB. 4 ERROR