ADEMCO AlarmNet 7835C, Руководство по установке

Страница: 16 / 38

– 16 –
Restoral Reporting Zone Selection (Questions 21-27)
Restoral reporting can be enabled or disabled. If you have programmed any of the zones for pulse
operation, then, following the restoral question, the 7720P will display "REST ON CHG (Y/N)". This
feature is used for zones connected to the bell output of a panel, and when enabled (by pressing “Y”) will
report the zone in restoral when the pulse train stops and a steady-state level, either high or low, is left on
the zone input or when the steady-state level starts pulsing. If you do not enable this feature (by pressing
“N”), the zone will only restore on a steady-state low logic level.
UL
Zone restoral must be enabled for UL installations.
Question 21
Rest. Z1 (Y/N)
Press “Y” to enable restoral reporting for zone 1. Press “N” to disable restoral
reporting
Question 21a
Rest. On CHG
(Y/N)
Press “Y” if restore is to be sent when the type of signal
changes, i.e., when pulsing state changes to a steady-state
level (high or low) or when a steady state changes to a
pulsing state. Restore normally occurs when the opposite
steady state occurs, e.g., when a steady-state high goes low.
Question 22
Rest. Z2 (Y/N)
Press “Y” to enable restoral reporting for zone 2. Press “N” to disable restoral
reporting.
Question 22a
Rest. On CHG
(Y/N)
Press “Y” if restore is to be sent when the type of signal
changes, i.e., when pulsing state changes to a steady-state
level (high or low) or when a steady state changes to a
pulsing state. Restore normally occurs when the opposite
steady state occurs, e.g., when a steady-state high goes low.
Question 23
Rest. Z3 (Y/N)
Press “Y” to enable restoral reporting for zone 3. Press “N” to disable restoral
reporting.
Question 23a
Rest. On CHG
(Y/N)
Press “Y” if restore is to be sent when the type of signal
changes, i.e., when pulsing state changes to a steady-state
level (high or low) or when a steady state changes to a
pulsing state. Restore normally occurs when the opposite
steady state occurs, e.g., when a steady-state high goes low.
Question 24
Rest. Z4 (Y/N)
Press “Y” to enable restoral reporting for zone 4. Press “N” to disable restoral
reporting.
Question 24a
Rest. On CHG
(Y/N)
Press “Y” if restore is to be sent when the type of signal
changes, i.e., when pulsing state changes to a steady-state
level (high or low) or when a steady state changes to a
pulsing state. Restore normally occurs when the opposite
steady-state occurs, e.g., when a steady state high goes low.
Question 25
Rest. Z5 (Y/N)
Press “Y” to enable restoral reporting for zone 5 Press “N” to disable restoral
reporting.
Question 25a
Rest. On CHG
(Y/N)
Press “Y” if restore is to be sent when the type of signal
changes, i.e., when pulsing state changes to a steady-state
level (high or low) or when a steady state changes to a
pulsing state. Restore normally occurs when the opposite
steady state occurs, e.g., when a steady-state high goes low.
Question 26
Rest. Z6 (Y/N)
Press “Y” to enable restoral reporting for zone 6. Press “N” to disable restoral
reporting.
Question 26a
Rest. On CHG
(Y/N)
Press “Y” if restore is to be sent when the type of signal
changes, i.e., when pulsing state changes to a steady-state
level (high or low) or when a steady-state changes to a
pulsing state. Restore normally occurs when the opposite
steady state occurs, e.g., when a steady state high goes low.