ABB TZIDC-200 Скачать руководство пользователя страница 52

Страница: 52 / 68

TZIDC-200, TZIDC-210, TZIDC-220

DIGITAL POSITIONER | 42/18-85-EN REV. E

… 11 Diagnosis / error messages

… TZIDC error codes

Error code

Possible cause

Impact

Troubleshooting the Instrument

Error while processing the measured
values, pointing to an error in the working
data (RAM).

The actuator is moved to the safe position.
After approx. 5 seconds, the positioner is
automatically reset and the RAM is
reinitialized.

If the error persists even after the positioner
has been reset, the device will need to be
returned to the manufacturer for repair.

Error during the table processing, pointing
to an error in the working data (RAM).

The actuator is moved to the safe position.
After approx. 5 seconds, the positioner is
automatically reset and the RAM is
reinitialized.

If the error persists even after the positioner
has been reset, the device will need to be
returned to the manufacturer for repair.

Error when verifying the checksum of the
configuration data (RAM).

The actuator is moved to the safe position.
After approx. 5 seconds, the positioner is
automatically reset and the RAM is
reinitialized.

If the error persists even after the positioner
has been reset, the device will need to be
returned to the manufacturer for repair.

Error in the processor function registers
(RAM).

The actuator is moved to the safe position.
After approx. 5 seconds, the positioner is
automatically reset and the RAM is
reinitialized.

If the error persists even after the positioner
has been reset, the device will need to be
returned to the manufacturer for repair.

Internal error.

The actuator is moved to the safe position.
After approx. 5 seconds, the positioner is
automatically reset.

If the error can be reproduced and occurs in
the same position after resetting, the device
must be returned for repair to the
manufacturer.

Содержание TZIDC-200





































































Результаты поиска

Содержание TZIDC-200

Отзывы:

Бренды по названию

Популярные бренды

ABB TZIDC-200, Инструкция по эксплуатации

Результаты поиска

Содержание TZIDC-200

Отзывы:

Бренды по названию

Популярные бренды