manualshive.com logo in svg

ABB ProcessMaster FEM611, Руководство по эксплуатации

Поделиться
Скачать
ABB ProcessMaster FEM611 Скачать руководство пользователя страница 50

50

FEM610 | 

PROCESSMASTER  |  OI/FEM610-EN REV. A

Menu / parameter
Device Setup
 . . .Access Control

Selection of submenu ‘...

Access Control

’ using   .

 . . .Sensor

Selection of submenu ‘...

Sensor

’ using   .

 . . .Transmitter

Selection of submenu ‘...

Transmitter

’ using   .

Device Setup /  . . .Sensor

Range Mode Config

Activation of the second measuring range for the mass and volume flow.
The setting can be performed separately for the mass flow rate (Qm) and volume flow (Qv). This means that it 

is possible to switch quickly between two measuring ranges (e.g. Qm Max and Qm Max2). Switching is 

performed via the parameters "Qm Range Mode", "Qv Range Mode".
•  Disabled: Second measuring range for mass and volume flow rate deactivated.
•  Qm and Qv: Second measuring range for mass and volume flow rate activated.
•  Qm only: Second measuring range for mass flow activated.
•  Qv only: Second measuring range for volume flow activated.
Default setting: Disabled

Qm Max DN

The value specifies the lower massflow rate a flow velocity of 32.8 ft/s (10 m/s).  The value is set automatically 

via the selected nominal size multiplied with the density set.

Qm Max 1

Setting of the upper measuring range value 1 (Measuring range = 0 ... Qm Max 1) for the mass flow for forward 
flow and reverse flow.  Default setting: 1 x QmaxDN

Qm Max 2

Setting of the upper measuring range value 2 (Measuring range = 0 ... Qm Max 2) for the mass flow for forward 
flow and reverse flow.  This parameter is only available if the value "Max2 active" has been selected for the 

parameter "Qm Range Mode".

Qm Range Mode

Manual switchover between the measuring ranges (Max1 active / Max2 active) for the mass flow 

measurement. This parameter is only available if the value Qm only or Qm and Qv has been selected for the 
parameter "Range Mode Config".

Qv Max DN

The value specifies the lower volume flowrate rate a flow velocity of 32.8 ft/s (10 m/s). The value is set 

automatically via the selected nominal size.

Qv Max 1

Setting of the upper measuring range value 1 (Measuring range = 0 ... Qv Max 1) for the volume flow for 
forward flow and reverse flow. Default setting: 1 x QmaxDN

Qv Max 2

Setting of the upper measuring range value 2 (Measuring range = 0 ... Qv Max 2) for the volume flow for 

forward flow and reverse flow.  

This parameter is only available if the value "Max2 active" has been selected for the parameter "Qv Range 

Mode".

Default setting: 1 x QmaxDN

Qv Range Mode

Manual switchover between the measuring ranges (Max1 active / Max2 active) for the volume flow 

measurement. This parameter is only available if the value Qv only or Qm and Qv has been selected for the 
parameter Range Mode Config".

Sensor Location Tag

Entry of the measuring point tag for the sensor.

Alphanumeric, max. 20 characters

Sensor Tag

Entry of the TAG number of the sensor.

Alphanumeric, max. 20 characters.

 . . .Operating Mode

Selection of submenu ‘...

Operating Mode

’ using   .

Device Setup /  . . .Access Control

Standard Password

Entry / change of the password for the ‘Standard’ access level.

Read Only Switch

Indicator of the position of the write protection switch.

For further information, see chapter "Write protection switch" on page 27.

7      . . .Operation

 . . .Parameter descriptions

Menu: Device setup

Содержание ProcessMaster FEM611





















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды