manualshive.com logo in svg

ABB ProcessMaster FEM611, Руководство по эксплуатации

Поделиться
Скачать
ABB ProcessMaster FEM611 Скачать руководство пользователя страница 29

29

FEM610 | 

PROCESSMASTER  |  OI/FEM610-EN REV. A

6     . . .Commissioning

Parameterization via the infrared service 

port adapter

Parameterization via the local operating 

interface

Configuration via the infrared service port adapter on the 
device requires a PC / notebook and the FZA100 infrared 
service port adapter.

All parameters can also be set using the HART DTM available 

at www.abb.com/flow and the "ABB AssetVision" software.

1 

Position the infrared service port adapter on the front 
plate of the transmitter as shown

2 

Insert USB interface cable into a free USB female 
connector on the PC / notebook.

3 

Switch on the device power supply.

4 

Start ABB AssetVision and perform the parameterization 

of the equipment.

Detailed information on operating the software is available in 
the relevant operating instructions and the DTM online help.

1 

Open device terminal box.

2 

Connect programming plug to the local operating 
interface of the device.

3 

Insert USB interface cable into a free USB female 
connector on the PC / notebook.

4 

Switch on the device power supply.

5 

Start ABB AssetVision and perform the parameterization 

of the equipment.

Detailed information on operating the software is available in 
the relevant operating instructions and the DTM online help.

A PC / notebook and the USB interface cable are required to 
configure the device via the device's local operating interface.
In conjunction with the HART-DTM and the software "ABB 

AssetVision" available at www.abb.com/flow, all parameters 

can also be set without the need for a local display.

G11911

RxD
TxD

3

2

1

 

G11625

1

2

3

4

Figure 41  Infrared service port adapter 
on transmitter (example)

Figure 42  Connection to the local operating interface

Infrared service port adapter

USB interface cable

PC / notebook running ABB AssetVision and HART DTM

Local operating interface

Programming plug  

PC / notebook

USB interface cable

1
2
3

1
2
3
4

Содержание ProcessMaster FEM611





















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды