ABB ProcessMaster FEM611 Скачать руководство пользователя страница 38

Страница: 38 / 84

FEM610 |

PROCESSMASTER | OI/FEM610-EN REV. A

7 . . .Operation

Error messages on the LCD display

In the event of an error, a message consisting of a symbol and
text (e.g. Electronics) appears at the bottom of the process
screen.

The text displayed provides information about the area in
which the error has occurred.

The error messages are divided into four groups in
accordance with the NAMUR classification scheme. The group
assignment can only be changed using a DTM or EDD:

Switching to the configuration level

(parameterization)

The device parameters can be displayed and changed on the
configuration level.

Use

to switch to the configuration level.

Select the desired level of access using

Confirm the selection with

Note

There are three levels of access. A password can be defined
for level "Standard".
There is no factory default password.

The error messages are also divided into the following areas:

Note

For a detailed description of errors and troubleshooting
instructions, please see

Diagnosis / error messages

page 62.

Process Display

Electronics

Process Display

Access Level

Read Only

Standard
Service

Back

Select

Symbol

Description

Error / failure

Function check

Outside of the specification

Maintenance required

Range

Description

Operation

Error / alarm due to the current operating conditions.

Sensor

Error / alarm of the flowmeter sensor.

Electronics

Error / alarm of the electronics.

Configuration

Error / alarm due to device configuration.

Access Level

Description

Read Only

All parameters are locked. Parameters are read only and
cannot be modified.

Standard

All the parameters can be changed.

Service

Only ABB Customer Service has access to the Service
menu.

Содержание ProcessMaster FEM611





















































































Результаты поиска

Содержание ProcessMaster FEM611

Отзывы:

Бренды по названию

Популярные бренды

ABB ProcessMaster FEM611, Руководство по эксплуатации

Результаты поиска

Содержание ProcessMaster FEM611

Отзывы:

Бренды по названию

Популярные бренды