manualshive.com logo in svg

ABB ProcessMaster FEM611, Руководство по эксплуатации

Поделиться
Скачать
ABB ProcessMaster FEM611 Скачать руководство пользователя страница 20

20

FEM610 | 

PROCESSMASTER  |  OI/FEM610-EN REV. A

Potting the terminal box on-site

Procedure

Preparation

Health hazard .

The two-component potting compound is toxic – observe 
all relevant safety measures.
Follow the Material Safety Data Sheet that are provided by 
the manufacturer prior to starting any preparations.

Hazard warnings:

•  R20: Harmful by inhalation.
•  R36 / 37 / 38: Irritating to eyes, respiratory system 

and skin.

•  R42 / 43: May cause sensitization by inhalation and 

skin contact.

Safety advice:

•  S23: Do not breathe gas/fumes/vapor/spray.
•  S24: Avoid contact with skin.
•  S37: Wear suitable gloves
•  S63: In case of accident by inhalation: remove casualty 

to fresh air and keep at rest.

•  Complete the installation before potting in order to 

avoid moisture penetration. Before starting, check all 
the connections for correct fitting and stability.

•  Do not overfill the terminal box. Keep the potting 

compound away from the O-ring and the gasket / 
groove (see Fig. 29).

•  Prevent the two-component potting compound from 

penetrating the cable conduit if an NPT 1/2" 
installation is used.

If the terminal box is to be potted subsequently on-site, a 
special  two-component potting compound can be 
ordered separately (order no.  D141B038U01). Potting is 
only possible if the sensor is installed horizontally. 
Observe the following instructions during work activity.

CAUTION

5      . . .Installation

1 

Cut open the protective enclosure of the two-component 
potting compound (see packing).

2 

Remove the connection clamp of the potting compound.

3 

Knead both components thoroughly until a good mix is 
reached.

4 

Cut open the bag at a corner. Perform work activity 
within 30 minutes.

5 

Carefully fill the terminal box with the two-component 
potting compound until the connection cable is covered.

6 

Wait a few hours before closing the cover in order to 
allow the compound to dry, and to release any possible 
gas.

7 

Ensure that the packaging material and the drying bag 
are disposed of in an environmentally sound manner.

 

G10676

1

2

3

4

5

Packing bag

Connection clamp

Two-component potting compound

Drying bag

Maximum filling level

1
2
3
4
5

Figure 29  Procedure

Содержание ProcessMaster FEM611





















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды