ABB AX416 Скачать руководство пользователя страница 60

Страница: 60 / 72

…7

CALIBRATION

…7.3

Factory Settings

Factory Settings Access Code

Enter the required code number (between 0000 and 19999) to gain access to the factory
settings. If an incorrect value is entered, access to subsequent frames is prevented and the
display reverts to the top of the page.

Calibrate Sensor A

Note.

The values in the display lines for sensor calibration are shown as examples only –

the actual values obtained will differ.

Sensor B calibration (dual input analyzers only) is identical to Sensor A
calibration.

See page 60.

Operating Page

– see Section 2.3.

Calibrate Input for Sensor A ?

If calibration is required select

Yes

otherwise select

Note.

To abort calibration, press the

key again at any time before calibration is

complete – see next page.

Millivolt Zero

Set the millivolt source to –1000mV.

The display advances automatically to the next step once a stable and valid value is
recorded.

Note.

The upper 6-segment display shows the measured input voltage. Once the signal

is within range the lower 6-segment display shows the same value and

Calib

is displayed

to indicate that calibration is in progress.

Millivolt Span

Set the millivolt source to +1000mV

The display advances automatically to the next step once a stable and valid value is
recorded.

Temperature Zero (100R)

Set the temperature simulator to 100



The display advances automatically to the next step once a stable and valid value is
recorded.

Continued on next page.

Factory Set Code

0000

FACTORY SETTINGS

-----

Cal. Sensor A

-----

A:mV Zero (-1V)

-1000

Calib

A:mV Span (+1V)

Calib

A:T.Zero (100R)

Ohms

Calib

Cal. Sensor B

Monitoring pH

-1000

A: T.Zero (1K0)

1000

100.0

Cal. Output 1

Calibrate I/P ?

-----

Yes

Monitoring Redox

Dual Redox

pH/Redox

Содержание AX416









































































Результаты поиска

Содержание AX416

Отзывы:

Похожие инструкции для AX416

Бренды по названию

Популярные бренды

ABB AX416, Руководство пользователя

Результаты поиска

Содержание AX416

Отзывы:

Похожие инструкции для AX416

Бренды по названию

Популярные бренды