ABB AX416 Скачать руководство пользователя страница 40

Страница: 40 / 72

…5

PROGRAMMING

5.6

Configure Outputs

Configure Output 1

Output 2 configuration (and Outputs 3 and 4 if option board fitted

and

analog

features enabled – see Section 7.3) is identical to Output 1 configuration.

Assign

Select the sensor and analog output required:

Sen.A

– pH/Redox (ORP)/mV for the selected sensor.

Sen.B
Temp.A

– Temperature for the selected sensor.

Temp.B
A-B

–

Difference between the Sensor A and Sensor B readings.

Note.

Sen.B

Temp.B

and

A-B

are applicable only to dual input analyzers.

Range

Select the analog output current range for the selected output.

Span Value

(or

Deg.C

Deg.F

A-B

) and

Adjust

are shown alternately on the upper display

line. Use the

and

keys to adjust the displayed reading to the required span value.

Note.

The minimum and maximum span values are determined by the

Zero Value

setting

(see next page) plus the minimum differential, e.g. to set

Span Value

to 0.00 pH, first set

Zero Value

to –2.00pH.

– 0.00 to 16.00 pH (minimum differential, 2.00pH)

Redox/ORP

– –1100 to 1200 mV (minimum differential, 100mV)

Temperature

– Deg. C 0.0 to 150.0 (minimum differential, 10



Deg. F 32.0 to 302.0 (minimum differential,18



A-B

– 0.00 to 14.00 pH (minimum differential, 2.00pH)

Note.

A-B

is applicable only to dual input analyzers.

Continued on next page.

Config. Output 1

-----

AO1: Assign

-----

AO1: Range

-----

CONFIG. OUTPUTS

-----

A-B

Temp.B

Sen.B

Temp.A

Sen.A

4-20mA

0-20mA

0-10mA

AO1: Zero Value

Config. Output 2

AO1: Span Value

7.00

0.00

Содержание AX416









































































Результаты поиска

Содержание AX416

Отзывы:

Похожие инструкции для AX416

Бренды по названию

Популярные бренды

ABB AX416, Руководство пользователя

Результаты поиска

Содержание AX416

Отзывы:

Похожие инструкции для AX416

Бренды по названию

Популярные бренды