ABB AX416 Скачать руководство пользователя страница 16

Страница: 16 / 72

…3

OPERATOR VIEW

3.2

View Outputs

Theoretical Analog Output

There are up to four analog outputs, each showing information for one sensor.

Note.

Analog outputs 3 and 4 available only if option board fitted

and

analog features

enabled – see Section 7.3.

Live current output value being retransmitted.

Current output shown as a percentage of full scale for the output range set in

CONFIG.

OUPUTS

– see Section 5.6.

See Section 3.3.

See Note on Page 13.

Advance to analog output 2 (and outputs 3 and 4 if option board fitted

and

analog features enabled – see Section 7.3).

3.3

View Hardware

Sensor A Module

Shows the type of input board fitted to the analyzer for the Sensor A input.

Sensor B Module

– Dual input analyzers only

Shows the type of input board fitted to the analyzer for the Sensor B input.

Option Board
Note.

Displayed only if the option board is fitted.

Displays the optional features enabled in the

Factory Settings

page – see Section 7.3.

See Section 3.4.

See Note on Page 13.

50.0

Analog Output 1

12.00

VIEW OUTPUTS

-----

VIEW HARDWARE

SENSOR CAL.

Security Code

CONFIG. DISPLAY

Analog Output 2

-----

Sensor A Module

VIEW HARDWARE

-----

Option Board

-----

Sensor B Module

-----

Pb Dp

Analog

VIEW SOFTWARE

SENSOR CAL.

Security Code

CONFIG. DISPLAY

VIEW HARDWARE

Содержание AX416









































































Результаты поиска

Содержание AX416

Отзывы:

Похожие инструкции для AX416

Бренды по названию

Популярные бренды

ABB AX416, Руководство пользователя

Результаты поиска

Содержание AX416

Отзывы:

Похожие инструкции для AX416

Бренды по названию

Популярные бренды