ABB AX416 Скачать руководство пользователя страница 18

Страница: 18 / 72

…3

OPERATOR VIEWS

The logbook stores data entries for alarm events, sensor errors, power failures and pH
calibration information.

View Logbook

Use the

and

keys to access the

Alarms

logbook.

Note.

If no entries are stored in the

Alarms

logbook, the display shows

No More Entries

Alarms

The

Alarms

logbook contains up to 10 entries (entry 1 is the most recent), each comprising

an alarm number, alarm state (On or Off) and the date/time of the occurrence.

Option board fitted

and

analog features enabled (Section 7.3) – see Section 3.6.

See Note on Page 13.

Advance to entries 2 to 10.

Note.

If no more entries are stored, the display shows

No More Entries

View Logbook

Use the

and

keys to access the

Errors

logbook.

Note.

If no entries are stored in the

Errors

logbook, the display shows

No More Entries

Errors

The

Errors

logbook contains up to 5 entries (entry 1 is the most recent), each comprising

the sensor letter, error number and the date/time of the occurrence.

Option board fitted

and

analog features enabled (Section 7.3) – see Section 3.6.

See Note on Page 13.

Advance to entries 2 to 5.

Note.

If no more entries are stored, the display shows

No More Entries

-----

11:09:02 12:34

VIEW CLOCK

SENSOR CAL.

Security Code

CONFIG. DISPLAY

Sen.A

VIEW LOGBOOK

Errors

Sen.A

Pt100

Alarms

Cals

Power

Errors

-----

11:09:02 12:34

VIEW LOGBOOK

-----

VIEW CLOCK

SENSOR CAL.

Security Code

CONFIG. DISPLAY

-----

VIEW LOGBOOK

Cals

Power

Errors

Alarms

3.5

View Logbook

Note.

The View Logbook function is available only if the option board is fitted

and

analog features enabled (Section 7.3)

and

Logbook

is set to

(Section 5.9).

Содержание AX416









































































Результаты поиска

Содержание AX416

Отзывы:

Похожие инструкции для AX416

Бренды по названию

Популярные бренды

ABB AX416, Руководство пользователя

Результаты поиска

Содержание AX416

Отзывы:

Похожие инструкции для AX416

Бренды по названию

Популярные бренды