ABB AX416 Скачать руководство пользователя страница 44

Страница: 44 / 72

5.10

Test Outputs and Maintenance

Test Outputs

Displays the output test details for the analog outputs.

Note.

Outputs 3 and 4 are available only if the option board is fitted

and

analog features

enabled – see Section 7.3.

Test Output 1

frame only is shown; the format of frames for the remaining outputs is

identical.

See below.

Test Output 1

The theoretical output current value.

Output current as a percentage of the full range current.

Use the

and

keys to adjust the displayed theoretical output current value to give the

output required.

See Section 7.3.

Test remaining outputs.

Maintenance

Hold Outputs

Enables the relay action and analog outputs to be maintained.

Auto.

– Changes in relay action and analog outputs are inhibited during sensor

calibration.

– Changes in relay action and analog outputs are inhibited.

Off

– Changes in relay action and analog outputs are not inhibited.

Note.

The LEDs flash while the analyzer is in 'Hold' mode.

Continued on next page.

See Section 7.3.

Hold Outputs

set to

Off

– return to main menu.

Hold Outputs

set to

Auto.

– continued on next page.

Test Outputs

-----

TEST/MAINTENANCE

-----

Test Output 1

4.00

20.0

Maintenance

-----

Hold Outputs

-----

Auto.

Off

FACTORY SETTINGS

Test Output 2

FACTORY SETTINGS

Load/Save Config

Maintenance

Automatic Time

…5

PROGRAMMING

Содержание AX416









































































Результаты поиска

Содержание AX416

Отзывы:

Похожие инструкции для AX416

Бренды по названию

Популярные бренды

ABB AX416, Руководство пользователя

Результаты поиска

Содержание AX416

Отзывы:

Похожие инструкции для AX416

Бренды по названию

Популярные бренды